FLUKE Ti32
Fluke 700HTP-2最大壓力：690bar接口：兩個1/4 in.NPT壓力端口
各一臺請報價.謝謝.
General descrtption
Main technical specification for drilling rig
Model of drilling rig 1000HP VFD slingshot drilling rig
Humidity： less than 90% at temperature of ＋20℃.
Altitude: ≤1000m
Rig work temperature range -18℃ to +50℃
Haz.Classification: As per API RP 500B
Parameter
Line 6×7
Diameter of drilling line Φ35mm（1 3/8″）
Rated input power of drawworks 1000kW(1360HP）
Gears of drawworks 1+1R variable frequency stepless speed- regulating
Opening diameter of rotary table Φ698.5mm(27 1/2″)
Rated power/No. of drilling pump 1300HP/ 2pcs
Type of mast K-type，cantilever
Effective height of mast 45m
Type of substructure Slingshot
Height of drill floor 9m
Clear height under rotary beam 7.6m
Volume of air tank 2×2m3+2m3 (Buffering tank)
No. of main generator set 1101bkw*3 (60Hz,600V)
Rated power x No. of auxiliary generator set 450ekw×1 (60Hz,480V)
Total power for drilling rig 3×1101bkW+450ekW
Diameter/rated pressure of drilling fluid manifold Φ102mm/35MPa
Total volume of mud tanks(include buffer tank) 300m3
Type of electric drive AC－DC－AC，common bus bar
Power/No. of drawworks' motors 1000kW /1
Power/No. of rotary table' motor 600kW /1
Power/No. of mud pump' motors 1000kW /2
Power/No. of drawworks' auxiliary drive motor 45kW /1
Hoisting system
Mast Assembly JJ315/45-K
Mast
Technical specification:
Conforming to API Spec 4F 3rd Edition and marked with API monogram.
Structural Safety Level (SSL) E2 and U2
Product Specification Level (PSL) PSL-1
Maximum static hook load capacity (5x6 line) (Note：Acceleration, impact, drill string racking and wind load will reduce max. hook load capacity) 3150kN(700,000lbs)
Available height of mast 45m
Top span(front×side) 2.1 m×2.05m
Bottom span 8m
Rated wind load for mast：
Expected(No hook load, no setback load) 47.8m/s(107mph)
Unexpected(No hook load, full of setback) 36m/s(80.5mph)
Operating 16.5m/s(36.9mph)
Erection 16.5m/s(36.9mph)
Transportation 16.5m/s(36.9mph)
Racking capacity of monkey board(5″drill pipe 28m stand) 180pcs ;9″drill collar 2pcs、8″drill collar 6pcs
Available height of monkey board 24.5m、25.5m、26.5m
Mast accessories
Equipped with following auxiliary components:
2 mast ladders (one on left to crown block and right side one to racking board)
2 climb assistors
1 standpipe work platform
3 dead line stabilizers
2 manual tong for balance weight
1 hydraulic power tong sheave
Racking board
One racking board with foldable table and fingerboard
All the fingerboard are equiped withed the safety cable,and foldable are equiped withed safety line.
Equiped with the banister
Equiped with install seat for air winch and sheave.
Equiped with suspension vertical column prevent falling, and urgency exit for derrick man.
Casing stabbing board
Available adjust casing centralization platform,equiped under the left lower end of the mast.
Raising and lowering of operation board by air winch.
Adjust scope for elevating movement of operation board 6M.
Substructure Assembly DZ315
Substructure
Technical specification:
Conforming to API Spec 4F 3rd Edition and marked with API monogram.
Structural Safety Level (SSL) E2 and U2
Product Specification Level (PSL) PSL-1
Maximum static hook load capacity 3150kN(700,000lbs)
Max. static load capacity for setback 1800kN
Load capacity with full setback and max. static hook load 4950kN
Floor height 9m
Clear height from rotary beam to ground 7.6m
Setback capacity(5″DP, 28m stand) 180pcs，9″drill collar 2pcs、8″drill collar 6pcs
Substructure attachments
Equipped with following attachments:
2 sets of installation accessories for 5t air winch
2 backup tail posts for manual tong
1 backup tail post for power DP tong
1 safety escape slide.
1 V-door ramp
Equipped with 3 ladders (one is on front floor side to ground, one is on rear floor side to ground, and the other is on right floor side to shaker tank)
Mud drip pan to be provided for rotary table
Bop handling beam(install under the top）
Supports for floor doghouse
BOP handling device DZ400
Technical specification：
Max. hoisting capacity 2×200kN
Lifting speed 0～1.6m/min
Lifting distance 3.2m
horizontal moving speed 0～12m/min
Operation Hydraulic
Rated pressure of hydraulic system 16MPa
Drawworks, JC40DB
Drawworks
The components of drawworks conform to API Spec 7K- 5th Edition
Technical specification：
Rated input power 1000kW
Max. pull of fastline 340kN
Diameter of wireline Φ35mm（1 3/8″）
Gears of drawworks Two gear stepless speed-regulating
Drum（diameter×length） Φ685mm×1245mm
Control type of speed and function AC frequency variable control + dynamic brake
Brake Disc hydraulic disc brake
Automatic bit-feed speed 0～60m/h（auxiliary drive device to be used)
0～200m/h（use main drive device)
Hydraulic disc brake
Technical specification：
Model PS80
Brake disc 1pcs
Safety caliper 3pcs
Service caliper 3pcs
Diameter of brake disc Φ1400mm
Rated positive pressure of brake caliper 80kN
Rated pressure of hydraulic disc brake operating system 7.5MPa
Cooling type of brake disc Air cooling(natural cooling)
AC frequency variable motor of drawworks
Technical specification：
Fundamental frequency power 1000kW
Fundamental frequency voltage 600V
Fundamental frequency current 1164 A
Fundamental frequency power factor 0.86
Fundamental frequency rotary speed 800 r/min
Fundamental frequency torque 11937Nm
Insulation class 200 class
Number of poles 6 poles
Connection mode for stator winding Y
Cooling type Forced air cooling(equipped with blower)
Working type Continuous
Explosion Proof Mark Exe.Ⅱ T3
Protection grade of junction box IP55 pressured junction box
Drawworks auxiliary drive motor
Rated power 45 kW
Coling tape forced wind cool
Motor protection degree IP55, Exd.
Auxiliary drive device
Technical specification:
Rated power 45kW
Speed range of bit-feed 0-60m/h
Feature：
The power of auxiliary AC variable frequency motor is input to the main gearbox via helical bevel gear reducer in order to drive the drum shaft.
VFD drive with digital control for auto-bit-feed
It is featured with high gear ratio and input torque, meeting the requirement of hoisting max. weight of drill string and it also can be used for emergency hoisting in case of failure of main system.
Crown block TC315
Technical specification:
Conforming to API Spec 8C 4th Edition/4F 3rd Edition specification
Structural Safety Level SSL E2 and U2
Product Specification Level PSL PSL-1
Max. static load 3150kN(700,000lbs)
Quantity of sheaves 6+1
OD of main sheave Φ1270mm
Diameter of wireline Φ35mm（1 3/8″）
5t 2 sets DW sheaves at bottom of crown block, all the derrick block with safety line
Travelling block, YC315
Technical specification:
Conforming to API Spec 8A/8C and marked with API monogram
Max. static load 3150kN(700,000lbs)
Quantity of sheave 6
OD of sheave Φ1270mm
Diameter of wireline Φ35mm（1 3/8″）
Hook, DG315
Technical specification:
Conforming to API Spec 8A/8C and marked with API monogram
Max. static load 3150kN(700,000lbs)
Stroke of spring 200mm
Opening size of main hook opening 220mm
Overall dimension（length×width×height） 2953×890×880mm
Weight 3420kg
Feature:
Hook is equiped with rotary locking device
Hook opening is equipped with reliable locking device
Deadline anchor, JZG34A
Technical specification:
Conforming to API Spec 8A/8C and marked with API monogram
Type of installation Horizontal
Sensor Tension type
Output pressure of sensor 6MPa
Max. pull of deadline 340kN
Diameter of wireline 35mm
Max. displayed load of weight indicator 4080kN （6*7）
Drilling wireline
Conforming to API 9A 25th Edition
Technical specification：
Type 6×19S+IWRC EIPS (left hand)
Diameter Φ35mm（1 3/8″）
Length 2200m
Wireline spooler DDS35
Max. diameter of wireline 2600mm
Max. width of wireline reel 1600mm
Power of motor: 7.5kW
Capacity 2300m(Φ35mm wireline)
Max.load-bearing 13000kg
Rotary system
Rotary table and independent drive system
Rotary table, ZP275
Conforming to API Spec 7K 5th Edition and marked with API monogram.
Max. static load 4500kN
Opening diameter Φ698.5mm(27 1/2″)
Max. rotary speed 220r/min
Gear ratio 3.56
Overall dimension 2468×1810×718mm
Weight(not including that of master bushing) 7548kg
Rotary table independent drive unit
Technical specification:
Continuous working torque 40000N•m
Short-time Max. working torque 52000N•m
Speed-regulating range of rotary table 0～220r/min
Model of inertia brake LT500/250T
Brake torque（0.8MPa） 26900 N•m
Weight（Including weight of rotary table) 12500kg
Frequency variable motor of rotary table
Fundamental frequency power 600kW
Fundamental frequency voltage 600V
Fundamental frequency current 712 A
Fundamental frequency power factor 0.86
Fundamental frequency rotary speed 660 r/min
Fundamental frequency torque 8686Nm
Fundamental frequency 33.5 Hz
Insulation class 200 class
Number of poles 6 poles
Connection mode for stator winding Y
Cooling type Forced air cooling(equipped with blower)
Working type Continuous
Explosion Proof Mark Exe.Ⅱ T3
Protection grade of junction box IP55
Weight 2600kg
Bushings for rotary table
The rotary table is equipped with the following bushings:
Master bushing
5 1/4” four pins driving roller bushing
4 1/4” four pins driving roller bushing
2 3/8”-8 5/8”bushing（for drilling）
9 5/8”-10 3/4”bushing,（for running 9 5/8” casing）
11 3/4”-13 3/8” bushing,（for 13 3/8” casing）
20” bushing,（for 20” casing）
Lift link for bushing
Swivel,SL450(with FMS-20 air motor)
Technical specification:
Conforming toAPI 8A/8C with API monogram
Max. static load 4500kN(1000,000lbs)
Max. dynamic load（API bearing load) 2800kN
Max. rotary speed 300r/min
Max. working pressure 35MPa
ID of stem 75mm
Thread of connection API / 6 ⅝″ Reg.LH
Connection between gooseneck and rotary hose,，Fig 1002 union
Model of air motor FMS-20
Rated rotary speed 2800r/min
Rated air pressure 0.6～0.8MPa
Rated power 14.7kW
Air consumption 17m3/min
Air inlet pipeline 1 ½″
Rated makeup rotary speed 92r/min
Max. makeup spinning torque 3000N·m
Overall dimension（length×width×height） 3,037×1,090×1,085mm
Weight 3461kg
Top Drive system TESCO
Hoisting 250 ton
m2bax225sMb4
m2bax280sa4
m2bax200mLA4
ABB M2BAX 225SMB4 45KW B3
M2BAX 280SA4 75KW B3
M2BAX 200MLA4 30KW B3
ABB ANALOG INPUT 16CH, 12BIT
0(4)-20MA,-20/20MA,-10/10V
AI620 P/N : 3BHT00005R1
HIGH SPEED COUNTER TYPE : DP620
5/24VDC,100KHZ,5CH P/N : 3BHT300016R1
ADVANT CONTROLLER 110
RACK BASIC UNIT P/N : 3BHT100011R1
ADVANT FIELD BUT 100
COMMUNICATON UNIT TYPE : CI630
P/N : 3BSE011000R1
POWER SUPPLY TYPE : SA168,F324V
30A,900VA,50/60HZ
24VDC,25A,LOAD RANGE :1-25A
P/N : 3BSE003389R1
CONNECTION UNIT ANALOG INPUT
BOARD TYPE :DSTA171,FOR 8CH
P/N : 3BSE018311R1
AF100 COAXIAL MODEM
TYPE : TC625 P/N : 3BSE002224R1
BATTERY UNIT SB520 NICD 12V
4AH P/N : 3BSC760004R1
"7695680Drehmomentschlüssel DREMOMETER
E im Kasten"
Versandkosten VK
西門子 01-46012B01
1501D04G09
1501D04G02
1501D16G05
01F7468602
01C47799A01
7506E06G03
58PTX100
