CARBO 2M鑄鐵型面堆焊使用 特 性可直接在鑄鐵上施焊,對于抗冷沖壓的金屬間磨耗非常有效.焊金第一層為奧氏體組織,從第二層開始為馬氏體組織抗磨耗性好. Can directly in the iron welding process, to make cold stamping metal abrasion very effective. Welding between the first layer of gold for austenitic group, second start martensite organization for good abrasion resistanceHRC46~52用 途球墨鑄鐵,火焰淬火鑄鐵,合金鑄鐵的直接堆焊. Ductile iron, flame hardening, alloy iron direct hardfacing.規 格2.6￠ 3.2￠ 4.0￠ 5.0￠ CARBO 2H鑄鐵刃口堆焊使用 特 性可直接在鑄鐵上施焊,對于抗冷沖壓的金屬間磨耗非常有效.焊金第一層為奧氏體組織,從第二層開始為馬氏體組織,抗磨耗沖壓性能優良. Can directly in the iron welding process, to make cold stamping metal abrasion very effective. Welding between the first layer of gold for austenitic group, second began to martensitic organization, abrasion resistance stamping excellent performance用 途主要用于各種淬火后鑄鐵的刃口修補焊接. Mainly used for various hardened iron blade repair welding.規 格2.6￠ 3.2￠ 4.0￠ 5.0￠ GNK-61N鑄鐵焊條 特 性有良好的抗拉強度和延伸率 硬度HB-160. Have good tensile strength and elongation hardness HB - 160.用 途用于各種鑄鐵 合金鑄鐵 鋼與鑄鋼的焊接. For all kinds of iron alloy steel and cast iron welding.規 格2.6￠ 3.2￠ 4.0￠ 5.0￠ GNK-67N焊條 特 性用于不同鑄鐵焊接時焊層能最大要求的滿足其顏色匹配,抗拉強度和延展性優良. Used for welding of different iron welding layer can satisfy the requirements of color matching, tensile strength and ductility.用 途焊補灰口鑄鐵,球墨鑄鐵. Weld-repair grey cast iron, ductile iron規 格2.6￠ 3.2￠ 4.0￠ 5.0￠ GNK-8C打底焊條 特 性高鉻成份,焊金具有高拉力,高韌性 HB-280. High chrome component, high strength, welding gold high toughness HB - 280.用 途鑄鋼模硬面制做打底緩沖層,裂縫敏感度較高的特種鋼接合襯焊使用. Cast steel hardfaced making render buffer layer, crack sensitive use of special steel lining welding joints.規 格2.6￠ 3.2￠ TM-2000模具硬化堆焊用 特 性對沖壓模的金屬磨耗非常有效,焊金第一次為奧氏體組織,第二層為高硬度的馬氏體組織.火焰淬火鋼也可以直接堆焊. The metal stamping mould for abrasion is very effective for the first time, welding gold austenitic organization, the second is the high hardness martensite steel quenching. Flame may also directly hardfacing.用 途直接堆焊各種鑄鐵材的模具. All sorts of cast iron material directly surfacing of mould.規 格2.6￠ 3.2￠ 4.0￠ 5.0￠ LKE-7號鋼焊條(SUPER-7) 特 性耐沖擊與金屬間磨耗,直接焊于熱處理后的Cr12MoV鋼上,可全位置焊接,硬度HRC52~57.Impact resistance and metal abrasion, directly welded to the Cr12MoV after heat treatment, but the position on the steel welding, hardness HRC52-57用 途汽車大型模具硬面制做,冷沖模刀口焊接Auto giant mould making, cold die cutting hardfaced welding.規 格2.6￠ 3.2￠ GNK-7A刃口焊條 特 性熔敷金屬具有高硬度的馬氏體組織,耐磨耗耐沖擊性能優良,硬度HRC55~58. Deposited metal of martensite with high hardness, good abrasion resistance, impact resistant performance of hardness HRC55 ~ 58.用 途切模,沖壓模具的刃口焊材,也可以在碳鋼上堆焊制成新工具. Cutting, welding blade of stamping mould, also can be made in the new tool steel #.規 格2.6￠ 3.2￠ 4.0￠ CARBO 6W各種刃口堆焊使用 特 性高鉻成份,耐磨耗耐龜裂性能優良,焊后硬度較高,機械加工困難. High chrome component, abrasion resistance, resistance to crack excellent performance after welding, machining difficulty high hardness.用 途淬火硬化模具鋼刃口的修補,適用于SKD11合金工具鋼,淬火后的模具鋼修補. Quench hardened steel blade of repair, applicable to SKD11 alloy steel, alloy after quenching repair.規 格2.6￠ 3.2￠ 4.0￠ UTP 673工模具焊條
