氣動鋼管FDJ-120風動鏈條鋸暢銷鏈條鋸 木材鏈鋸 防爆風動鏈鋸 FDJ-120風動鏈鋸價格 FDJ-120型風動鏈條鋸是我公司精心研制的煤礦巷道支護維修、截割木材的專用工具。代替了手藝刀鋸截木材,減輕了人們粗笨體力勞動,又進步截割速度。煤礦井下風源方便,安上風管即可作業,且不受防爆的約束,適用于瓦斯煤礦出產的需求,深受廣闊用戶的歡迎。
聯系人金經理電話：13934240041
24小時銷售熱線歡迎大家致電咨詢謝謝

1.礦用軌跡輕型3分鐘軌跡重型5分鐘三.長處1.90°直切,45°斜切,立式切開一體機。 2.工作速度只要砂輪機的1/60,安全無火花。 3.切縫窄0.5mm,切開外表平整，精度高，無掛渣，無脫碳。 4.鋸條使用壽命長，單位切開成本低，一根鋸條使用壽命等同于50-80片砂輪切開片，較電能鋸節能60%。

山西萬澤錦達機械制造有限公司聯系人金經理電話13934240041
型號FDJ-120鋼管風動切割鋸礦用切割鋸多功能切割鋸歡迎致電咨詢

使用方法： 1、了解所需切開的資料，如有必要能夠經過下降空氣壓力來下降鋸片的滾動速度。 2、確保結實固定了所需切開的資料，避免其移動。 3、氣動空氣馬達時，用手指按壓閥桿，然后開端切開。 4、用鋸的分量來控制切開壓力。關于較軟的資料來說，這樣的分量現已滿足。過多的壓力會下降鋸片的速度。關于較硬的資料，能夠經過加壓的方式來下降鋸片的滾動速度。切開是堅持鋸垂直。鋸片的任何扭曲或傾斜都可能下降其使用壽命。（留意：避開切開后可能墜落的碎片。切開行將完成時，切勿使鋸碰到您的身體、工件或鄰近的其它人員。） 5、封閉空氣馬達時，開釋閥桿。 6、下次切開開端前，鋸片有必要堅持運動狀況。氣動鋸時，鋸片不能觸摸任何外表。 7、斷開空氣軟管時，封閉空氣軟管閥。斷開前，先翻開空氣閥給軟管減壓。 8、更換鋸片前，務必斷開空氣軟管，并推進閥桿以開釋掉馬達內的壓力。 9、順時針滾動調整手柄以便開釋鋸片導桿上的張力。然后開釋側面板的鎖以便翻開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開

How to use: 1, understand the material that needs to be cut, if it is necessary to reduce the rolling speed of the saw blade through the downward air pressure. 2, ensure sturdy and fixed the required cut data to avoid its movement. 3. When pneumatic air motor, press the stem with the finger, and begin to cut. 4, the cut pressure is controlled by the component of the saw. For softer data, such components are now satisfied. Too much pressure will reduce the speed of the saw blade. With more hard data, the rolling speed of the saw blade can be reduced by pressure. The incision is to stick to the saw vertical. Any twist or tilt of the saw may decrease its service life. (notice: avoid fragments that may fall after a cut. When the cut will be completed, do not make the saw touch your body, the workpiece, or the other people in the neighborhood. 5. When the air motor is closed, the stem is released. 6. Before the next opening, it is necessary to adhere to the movement of the saw blade. When a pneumatic saw, a saw can't touch any appearance. 7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. 8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane. 9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the guide rod of the saw