FDJ-120風動手持切割鋸是我公司針對高危，安全系數要求特別高的工作環境，如化工.治煉廠.天然氣開采.高危潮濕的隧道，水下及狹窄的空間作業，尤其是高瓦斯防爆礦井。山西萬澤錦達礦山機械設備有限公司自主研發的新型多用途風動手持切割工具。它使用臺灣進口氣動馬達作為動力輸出，利用壓縮空氣作為動力源，不用電源。風動手持切割鋸不但整機重量輕，操作簡單，攜帶方便零火花，提高工作效益。本產品安全可靠是高危行業的理想氣動切割工具。

一．技術參數:1適用材料:不銹鋼.鋁，銅.鉻合金，鎳基合金，玻璃，纖維，木材，塑料，鋼絲繩等。2切割范圍：120mm*120mm圓型材料，220mm*120mm方型材料。3工作壓力：0.3—0.8Mpa4外型尺寸：650*210*270

二．礦用軌道輕型3分鐘軌道重型5分鐘三.優點1.90°直切,45°斜切,立式切割一體機。2.運轉速度只有砂輪機的1/60,安全無火花。3.切縫窄0.5mm,切割表面平整，精度高，無掛渣，無脫碳。4.鋸條使用壽命長，單位切割成本低，一根鋸條使用壽命等同于50-80片砂輪切割片，較電能鋸節能60%

 貴州安順FDJ-230高效率切割鋸廠家批發

 聯系人金經理13934240041

 微信號13934240041

使用方法：

1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。

2、確保牢固固定了所需切割的材料，防止其移動。

3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。

4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）

5、關閉空氣馬達時，釋放閥桿。

6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。

7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。

8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。

9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開

 Cutting saw product parameter 1
Product introduction:. FDJ-120 pneumatic cutting saw is suitable for dangerous working environment. It can operate in a high temperature environment without sparks. It has no leakage hazard in wet environment. It is one of the ideal pneumatic tools with reliable performance, safety and high efficiency. It is widely used in mining, petrochemical, construction and other industries. Use the downhole air pressure pipe system as a power source. Light weight, easy to carry; structure science, easy to work. It can quickly cut pipe, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on. Super - Han metal steel alloy saw blade, high temperature resistance, wear resistance, long service life. It is very suitable for sawing stainless steel, nickel base alloy, iron, copper, aluminum, glass, plastic, wood and so on. Technical parameters: model 120 power 4kw power consumption 0.6 cutting width (diameter) 120mm saw blade speed 60m/min weight 6kg
Contact gold manager phone 13934240041





The use of pneumatic pneumatic cutting saws: 1, knowing the data needed to cut, if necessary to reduce the speed of change of the saw blade through the downward air pressure. 2, ensure the sturdy fixation of the required open data to avoid its movement. 3. When pneumatic air motor, press the stem with the finger, and begin to cut. 4, use the component of the saw to control the cut pressure. For softer data, such components are now satisfied. Too much pressure will reduce the speed of the saw blade. With more hard data, the speed of the change of the saw blade can be reduced by a pressurized method. The incision is to stick to the saw vertical. Any skew or tilt of the saw can reduce its service life. (notice: avoid fragments that can fall after a cut. Do not make the saw touch your body, the workpiece, or the other people in the neighborhood when the cut will be finished. 5. When the air motor is closed, the stem is released. 6. Before the next opening, it is necessary to adhere to the movement of the saw blade. When a pneumatic saw, a saw can't touch any appearance. 7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. 8. Before replacing the saw, you must disconnect the air hose and push the stem to release the pressure of Madane. 9, adjust the handle clockwise to release the tension on the guide rod of the saw blade. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. Shanxi million Zejin of mining machinery and Equipment Co. Ltd is a professional engaged in mine cutting saw, bolt cutting saw, pneumatic U type steel cutting saw, explosion-proof pneumatic anchor cutting sawing machine. Use: the product is divided into electric cutting machine and manual cutting machine, it can quickly and effectively cut reinforced high strength and no material in spark places need to cut, especially used in mine roadway repair, excavation and supporting, etc., the shear bolts, cutting range in diameter under 24mm shear machine, the product design is reasonable, safe and reliable, and improve work efficiency, reduce the labor intensity of the workers.


Product Descrtption: this saw is suitable for safe working environment. It can operate in high temperature environment without spark. It is one of the ideal pneumatic tools with reliable performance, safety and high efficiency. It is used in cable, square tube, building and other industries. ??? use air compressor as a power source. Light weight, easy to carry; structure science, easy to work. ??? - fast cutting pipes, cables, steel, steel, steel, U-shaped chain, anchor, etc.. ??? - indium metal super steel alloy saw blade, high temperature resistance, wear resistance, long service life. No spark pneumatic cutting saw by the compressed air as working medium, suitable for driving or working faces various working environments of hand-held pneumatic cutting saw structure of high strength, impact resistance, adapt to the harsh working environment of underground steel pneumatic cutting saw patent, and speed of air cooling structure design avoids cutting spark of coal mine gas cutting saw is used in underground dangerous environments can be used outside water or emulsion for cooling of the saw blade, improve service life and eliminate hidden spark by using different kinds of saw, cut from alloy steel to rubber, timber, wood products, plastic and other materials for cutting large diameter material or continuous operation time is long can supported by special support, greatly reduce the labor intensity, improving the safety of the operation