產品（礦用風動/氣動切割鋸）介紹：
1.該鋸適用于危險的工作環境，可在較高溫的環境下作業，無火花，在潮濕的環境中無漏電危險，是一款性能可靠、安全型及效率極高的理想風動工具之一。廣泛用于采礦、石化、建筑等行業。
2.利用井下壓風管道系統作為動力源。重量輕，易攜帶；結構科學，便于作業。
3.可快速切割管道、電纜、角鋼、結構鋼、U型鋼、鏈條、錨桿、錨索等。
4.錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。
山西萬澤錦達機械制造有限公司
德國進口切割鋸
聯系人金經理13934240041
技術參數：
型號 FDJ-120
功率 0.5kw
耗氣量 0.6
切割寬度（直徑） 120mm
鋸片速度 60m/min
重量 6kg
使用方法：
1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。
2、確保牢固固定了所需切割的材料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。
4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。
（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
5、關閉空氣馬達時，釋放閥桿。
6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。
8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。
9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開
山西萬澤錦達機械制造有限公司
德國進口切割鋸
聯系人金經理13934240041
ommodity introduction:
The FDJ-120 type pneumatic cutting saw is suitable for the risk working environment. It can operate in a high temperature environment, no sparks, and no leakage risk in humid environment. It is a reliable, safe and highly efficient aspiration pneumatic thing. It is widely used in mining, petrochemical, construction and other professions.
Use the downhole air pressure pipe system as a power source. The weight is light and easy to be carried; it is scientific and easy to work. Si Li Zhen FDJ-120/ mine explosion-proof cutting saw
Open pipe, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on.
- Han metal steel alloy saw blade, high temperature resistance, long life, the use of conflict. It is suitable for sawing stainless steel, nickel base alloy, iron, copper, aluminum, glass, plastic, wood and so on.
Technical parameters:
Type of type power consumption cut width cut width (diameter) speed weight of saw blade
FDJ-120 0.5KW 0.6m3/min three saws:
0 - 30mm
30 - 50mm
50 - 120mm 120mm 60m/min 6kg
FDJ-180 1.0kw 1.2m3/min 180mm 90m/min 10kg
FDJ-230 1.5kw 1.5m3/min 230mm 120m/min 16KG
Primary incision range:
The FDJ-120/220/230 pneumatic cut saw used the downhole pressure pipe system as a power source.
Light weight, easy to take; construction of science, easy to work.
The pipeline, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on can be cut off quickly.
Super - Han metal steel alloy saw blade, high temperature resistance, long life, the use of conflict.
Widely used in natural gas, coal mine, petrochemical, construction and other professions.
Pneumatic pneumatic cut saw application method:
1. Knowing the material that needs to be cut, it is necessary to reduce the speed of the saw blade by reducing the pressure of the air. Longting District FDJ-120 mine pneumatic cutting saw
2. It is true that the health-care stout has fixed the required cut materials to prevent it from moving.
3. When pneumatic air motor, press the stem with the finger, and then cut it initially.
4, the cutting pressure is controlled by the weight of the saw. This weight is now satisfactory for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of the saw blade can be reduced by pressure. The incision is to keep the saws straight. Saw any distortion or skew can reduce the use of life. (notice: avoid debris that can fall after a cut. When the cut is about to end, do not make the saw touch your body, the workpiece, or the other people in the neighborhood.
5. When the air motor is closed, the stem is released.
6. Before the next incision, it is necessary to adhere to the movement of the saw blade. The saw blade can't contact any surface when a pneumatic saw. Yanshi city FDJ-120/ mine explosion-proof cutting saw
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Note:
All power things may be very risky. Please follow the following safety procedures in order to maintain yourself.
1, wear goggles, gloves, safety boots and protective clothing.
2, time to adhere to the feet of stability, balance. Xuchang city mine / small portable pneumatic cutting saw
3, medical treatment, alcohol or drugs do not operate the things.
4. Before placing the machine, turn off the machine first (closed valve).
5. After the machine stops working, the supply of gas should be cut off immediately to prevent the machine from launching under the unconsciousness.
6. Do not stand on the ladder or operate on the scaffolding. Please stay away from the operation area.
7, operation to launch a clamp, should first remove the hose. Turn off the main valve. To release the compressed gas, then turned away from the valve.
8, hold the machine with both hands. Keep the rest of your hands and body away from the open area.
9, the motor must be turned off before transporting the machine and the gas source is cut off.
10, pay attention to the debris that may fall.
