FDJ-230多功能切割鋸黃石用途FDJ型輕軌切割鋸宜昌哪家好？？FDJ-230高強度切割鋸圖木舒克原料FDJ-230多功能切割鋸黃石用途高品質氣動風動切割鋸桂林質量杠杠的FDJ-120油氣管道切割鋸甘南怎么樣井下防爆風動氣動切割鋸蘇州哪里便宜

FDJ-120風動手持切開鋸是我公司關于高危，安全系數請求特別高的作業環境，如化工.治煉廠.天然氣挖掘.高危潮濕的地道，水下及狹窄的空間作業，尤其是高瓦斯防爆礦井。山西萬澤錦達礦山機械設備有限公司自立研制的新式多用途風動手持切開東西。它使用臺灣進口氣動馬達作為動力輸出，使用壓縮空氣作為動力源，不必電源。風動手持切開鋸不光整機分量輕，操作簡略，攜帶方便零火花，進步作業效益。本商品安全可靠是高危職業的抱負氣動切開東西。

聯系人金經理電話13934240041

FDJ-120風動切割鋸技術參數:

1：適用資料:不銹鋼.鋁，銅.鉻合金，鎳基合金，玻璃，纖維，木材，塑料，鋼絲繩等。

2：切開規模：120mm*120mm圓型資料，220mm*120mm方型資料。

3：作業壓力：0.3—0.8Mpa

4：外型尺度：650*210*270

FDJ-120風動切割鋸長處

1：90°直切,45°斜切,立式切開一體機。

2：運轉速度只要砂輪機的1/60,安全無火花。

3：切縫窄0.5mm,切開外表平整，精度高，無掛渣，無脫碳。

4：鋸條使用壽命長，單位切開成本低，一根鋸條使用壽命等同于50-80片砂輪切開片，較電能鋸節能60%

FDJ-120風動切割鋸使用方法：

1、了解所需切開的資料，如有必要能夠經過下降空氣壓力來下降鋸片的滾動速度。礦用錨桿錨索切割鋸寧夏 優質

2、保證結實固定了所需切開的資料，避免其移動。

3、氣動空氣馬達時，用手指按壓閥桿，然后開端切開。

4、用鋸的分量來操控切開壓力。關于較軟的資料來說，這么的分量已經滿足。過多的壓力會下降鋸片的速度。關于較硬的資料，能夠經過加壓的方法來下降鋸片的滾動速度。切開是堅持鋸垂直。鋸片的任何歪曲或傾斜都也許下降其使用壽命。（留意：避開切開后也許墜落的碎片。切開行將完結時，切勿使鋸碰到您的身體、工件或鄰近的其它人員。）

5、封閉空氣馬達時，開釋閥桿。

6、下次切開開端前，鋸片有必要堅持運動狀況。氣動鋸時，鋸片不能觸摸任何外表。

7、斷開空氣軟管時，封閉空氣軟管閥。斷開前，先翻開空氣閥給軟管減壓。

8、替換鋸片前，有必要斷開空氣軟管，并推進閥桿以開釋掉馬達內的壓力。

9、順時針滾動調整手柄以便開釋鋸片導桿上的張力。然后開釋側面板的鎖以便翻開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。

Cutting materials and applicable scope: (hand held explosion-proof cutting saw is mainly used for cutting coal mines, high gassy mines, oil pipelines, natural gas pipelines, cables and so on, which requires no sparks in the cutting process).
Iron, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U steel, H steel, steel, steel, steel, coal miners C steel rail.
FDJ-120 type mine emulsion pipe cutting saw, cable emulsion non spark cutting saw, the emulsion of -120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, chain saw, cutting off the coal mine FDJ-120 type mine anchor cable cutting saw, pneumatic hand-held cutting saw no spark...
FDJ-120/180/230 hand-held emulsion / wind cutting saw use method:
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When the emulsion motor is motor, the stem is pressed with the finger and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Shanxi million Zejin Machinery Equipment Manufacturing Co., in 2002 began to engage in the specific work of mining engineering, then according to their own demand, starting their own R & D and production of series of mining machinery needs, and transformation into today, customers all over the country, machinery manufacturing industry leader. It is a factory specializing in mining equipment, the company produces the mine / emulsion pneumatic cutting saw technology mature, the quality is excellent.