“十年老店，完備售后，信譽信賴” 是專業塑膠原料供應商

本司貨源穩定充足，發貨準時，交期和質量均有保障！
根據客戶要求，可提供塑膠原料相關報告。如：ROHS(SGS)報告，UL認證，材質證明及物質安全資料表（MSDS）！

價格合理,誠信經營，可全國供貨（廣東省內 免費送貨上門）。

歡迎來電咨詢7*24全天候服務熱線：13686017791 易小姐 QQ：335171600

注塑工藝各工序的溫度控制

1.料筒溫度：

熔料溫度是很重要的，所用的射料缸溫度只是指導性。熔膠溫度可在射嘴處量度或使用空氣噴射法來量度。射料缸的溫度設定取決于熔膠溫度、螺桿轉速、背壓、射料量和注塑件周期。您如果沒有加工某一特定級別塑料的經驗，請從最低的設定開始。

為了便于控制，射料缸分了區，但不是所有都設定為相同溫度。如果運作時間長或在高溫下操作，請將第一區的溫度設定為較低的數值，這將防止塑料過早熔化和分流。注塑件開始前，確保液壓油、料斗封閉器、模具和射料缸都處于正確溫度下。

2.熔料溫度：

熔體溫度對熔體的流動性能起主要作用，由于塑膠沒有具體的熔點，所謂熔點是一個熔融狀態下的溫度段，塑膠分子鏈的結構與組成不同，因而對其流動性的影響也不同，剛性分子鏈受溫度影響較明顯，如PC、PPS等，而柔性分子鏈如：PA、PP、PE等流動性通過改變溫度并不明顯，所以應根據不同的材料來調校合理的注塑件溫度。

3.模具溫度：

有些塑膠料由于結晶化溫度高，結晶速度慢，需要較高模溫，有些由于控制尺寸和變形，或者脫模的需要，要較高的溫度或較低溫度，如PC一般要求60度以上，而PPS為了達到較好的外觀和改善流動性，模溫有時需要160度以上，因而模具溫度對改善產品的外觀、變形、尺寸，膠模方面有不可抵估的作用。

4.注射壓力：

熔體克服前進所需的阻力，直接影響產品的尺寸，重量和變形等，不同的塑膠產品所需注射壓力不同，對于像PA、PP等材料，增加壓力會使其流動性顯著改善，注射壓力大小決定產品的密度，即外觀光澤性。它沒有固定的數值，而模具填充越困難，注塑件壓力也增大。

部分型號部分物性表

LDPE (low density polyethylene LDPE /1070 MG 24/ #) France akema
Use: other
Characteristic notes: good surface appearance, high gloss
Important parameters: melt flow rate: 9.2 g/10min density: 0.924 g/cm3 water absorption: 0.01% oxygen index: 18%, tensile strength: 12 MPa, elongation at break: 50% VEKA softening point: 94 degrees.
Manufacturer: Arkema
LDPE (low density polyethylene LDPE #) /NUC-8013/ Japan Younika
Use: film grade
Note: smooth characteristics: L
Important parameters: melt flow rate: 0.35 g/10min density: 0.925 g/cm3 tensile strength: 22 MPa breaking elongation: 600% hardness: 240 VEKA softening point: 93 C
Manufacturer: onica Corporation, Japan
LDPE (low density polyethylene LDPE #) /760/ MPI
Use: other
Note: the characteristics of compliance good stripping good heat sealing in low shrinking food contact
Important parameters: melt flow rate: 5.7 g/10min density: 0.921 g/cm3 tensile strength: 10.3 MPa breaking elongation: 480%
Manufacturer: MPI company, USA
LDPE (low density polyethylene # LDPE) /SSS 1018/ TPI in Thailand
Use: other
Feature notes: FDA 21 CFR 177.1520
Important parameters: melt flow rate: 45 g/10min density: 0.922 g/cm3 tensile strength: 7.5 MPa breaking elongation: 230% hardness: 48 VEKA softening point: 78 C
Manufacturer: Thailand TPI Polene Co., Ltd.
LDPE (low density polyethylene # high-pressure polyethylene) /LF0250/KJ/ Iran petrochemical
Use: film grade
Characteristic notes: good elastic extrusion and superior mechanical properties
Important parameters: melt flow rate: 2.5 g/10min density: 0.921 g/cm3 tensile strength: 11 MPa breaking elongation: 500%
Manufacturer: Iran national Petrochemical Industries Co
LDPE (low density polyethylene # high-pressure polyethylene) /LT0470/KJ/ Iran petrochemical
Purpose: film grade
Characteristic notes: good elastic extrusion and superior mechanical properties
Important parameters: melt flow rate: 4.7 g/10min density: 0.924 g/cm3 tensile strength: 12 MPa breaking elongation: 500%
Manufacturer: Iran national Petrochemical Industries Co
LDPE (low density polyethylene # high-pressure polyethylene) /B21/0.5/ Romania rompetrol
Use: film grade
Important parameters: melt flow rate: 0.5 g/10min density: 0.921 g/cm3 tensile strength: 13 MPa breaking elongation: 350% VEKA softening point: 90 C
Manufacturer: rompetrol Petrochemical Industries Co, Romania
LDPE (low density polyethylene # high-pressure polyethylene) /B22/0.7/ Romania rompetrol
Purpose: film grade
Important parameters: melt flow rate: 0.7 g/10min density: 0.921 g/cm3 tensile strength: 13 MPa breaking elongation: 350% VEKA softening point: 90 C
Manufacturer: rompetrol Petrochemical Industries Co, Romania
LDPE (low density polyethylene # high-pressure polyethylene) /B22/0.25/ Romania rompetrol
Purpose: film grade
Important parameters: melt flow rate: 0.25 g/10min density: 0.92 g/cm3
Manufacturer: rompetrol Petrochemical Industries Co, Romania
LDPE (low density polyethylene # high-pressure polyethylene) /UB-2141/03/ Brazil Quattor
Use: other
Characteristic notes: acceptable, good processing, slippage of food contact
Important parameters: melt flow rate: 4.1 g/10min density: 0.921 g/cm3 tensile strength: 25 MPa breaking elongation: 680% VEKA softening point: 89 C
Manufacturer: Quattor Petrochemical Industries Co, Brazil
LDPE (low density polyethylene LDPE polymer /MBW3282/AO/ Singapore #)
Purpose: film grade
Important parameters: melt flow rate: 1 g/10min density: 1.73 g/cm3
Manufacturer: Singapore polymer Co., Ltd.
LDPE (low density polyethylene # high-pressure polyethylene) /LD10919/ India Chemical Resources
Use: other
Characteristic notes: compliance of food contact
Important parameters: melt flow rate: 10 g/10min density: 0.919 g/cm3 tensile strength: 8.96 MPa breaking elongation: 16% flexural modulus: 228 MPa
Manufacturer: Chemical Resources, India
LDPE (low density polyethylene # high-pressure polyethylene) /LD15920/ India Chemical Resources
Use: other
Characteristic notes: compliance of food contact
Important parameters: melt flow rate: 15 g/10min density: 0.92 g/cm3 tensile strength: 10.3 MPa breaking elongation: 14.9% flexural modulus: 228 MPa
Manufacturer: Chemical Resources, India
LDPE (low density polyethylene # high-pressure polyethylene) /LD24921/ India Chemical Resources
Use: other
Characteristic notes: compliance of food contact
Important parameters: melt flow rate: 24 g/10min density: 0.921 g/cm3 tensile strength: 8.96 MPa breaking elongation: 14% flexural modulus: 234 MPa
Manufacturer: Chemical Resources, India
LDPE (low density polyethylene LDPE #) /LD225AA/ M.Holland
Use: other
Characteristic notes: good toughness
Important parameters: melt flow rate: 2 g/10min density: 0.92 g/cm3 tensile strength: 24.8 MPa breaking elongation: 300%
Manufacturer: M.Holland company, USA
LDPE (low density polyethylene LDPE #) /LD225MM/ M.Holland
Use: other
Characteristic notes: good toughness
Important parameters: melt flow rate: 2 g/10min density: 0.92 g/cm3 tensile strength: 22.8 MPa breaking elongation: 300%
Manufacturer: M.Holland company, USA
LDPE (low density polyethylene LDPE #) /WPP531/ Southern
Use: other
Feature notes: Institutional rating: FDA 21 CFR 177.1520
Important parameters: melt flow rate: 7 g/10min density: 0.917 g/cm3 fracture elongation: 600% flexural modulus: 207 MPa hardness: 47 embrittlement temperature: -87.2 C
Manufacturer: Southern Polymer, USA
LDPE (low density polyethylene LDPE #) /WPP551/ Southern
Use: other
Feature notes: Institutional rating: FDA 21 CFR 177.1520
Important parameters: