“十年老店，完備售后，信譽信賴” 是專業塑膠原料供應商

本司貨源穩定充足，發貨準時，交期和質量均有保障！
根據客戶要求，可提供塑膠原料相關報告。如：ROHS(SGS)報告，UL認證，材質證明及物質安全資料表（MSDS）！

價格合理,誠信經營，可全國供貨（廣東省內 免費送貨上門）。

歡迎來電咨詢7*24全天候服務熱線：13686017791 易小姐 QQ：335171600

注塑工藝各工序的溫度控制

1.料筒溫度：

熔料溫度是很重要的，所用的射料缸溫度只是指導性。熔膠溫度可在射嘴處量度或使用空氣噴射法來量度。射料缸的溫度設定取決于熔膠溫度、螺桿轉速、背壓、射料量和注塑件周期。您如果沒有加工某一特定級別塑料的經驗，請從最低的設定開始。

為了便于控制，射料缸分了區，但不是所有都設定為相同溫度。如果運作時間長或在高溫下操作，請將第一區的溫度設定為較低的數值，這將防止塑料過早熔化和分流。注塑件開始前，確保液壓油、料斗封閉器、模具和射料缸都處于正確溫度下。

2.熔料溫度：

熔體溫度對熔體的流動性能起主要作用，由于塑膠沒有具體的熔點，所謂熔點是一個熔融狀態下的溫度段，塑膠分子鏈的結構與組成不同，因而對其流動性的影響也不同，剛性分子鏈?zhǔn)軠囟扔绊戄^明顯，如PC、PPS等，而柔性分子鏈如：PA、PP、PE等流動性通過改變溫度并不明顯，所以應根據不同的材料來調校合理的注塑件溫度。

3.模具溫度：

有些塑膠料由于結晶化溫度高，結晶速度慢，需要較高模溫，有些由于控制尺寸和變形，或者脫模的需要，要較高的溫度或較低溫度，如PC一般要求60度以上，而PPS為了達到較好的外觀和改善流動性，模溫有時需要160度以上，因而模具溫度對改善產品的外觀、變形、尺寸，膠模方面有不可抵估的作用。

4.注射壓力：

熔體克服前進所需的阻力，直接影響產品的尺寸，重量和變形等，不同的塑膠產品所需注射壓力不同，對于像PA、PP等材料，增加壓力會使其流動性顯著改善，注射壓力大小決定產品的密度，即外觀光澤性。它沒有固定的數值，而模具填充越困難，注塑件壓力也增大。

部分型號部分物性表

LDPE (low density polyethylene # high-pressure polyethylene) /E6838-902F/ West Lake
Use: other
Characteristic notes: acceptable, slippage of food contact
Important parameters: melt flow rate: 1.3 g/10min density: 0.92 g/cm3 tensile strength: 30 MPa breaking elongation: 200% VEKA softening point: 92 C
Manufacturer: West Lake Chemical Co., Ltd.
LDPE (low density polyethylene # high-pressure polyethylene) /H2-26T/ Turkey Petkim
Purpose: film grade
Important parameters: melt flow rate: 1.5 g/10min density: 0.923 g/cm3
Manufacturer: Turkey Petrochemical holding company
LDPE (low density polyethylene # high-pressure polyethylene) /F2-26TO/ Turkey Petkim
Use: film grade
Important parameters: melt flow rate: 2.1 g/10min density: 0.924 g/cm3
Manufacturer: Turkey Petrochemical holding company
LDPE (low density polyethylene LDPE /FB3000/LG chemical #)
Use: film grade
Characteristic notes: characteristics: transparency, tension and good processability
Important parameters: melt flow rate: 3 g/10min density: 0.92 g/cm3, notched impact strength: 120 tensile strength: 17 MPa, elongation at break: 500% VEKA softening point: 90 C embrittlement temperature: -76 C.
Manufacturer: Korea LG chemical company
LDPE (low density polyethylene LDPE /FB2000/LG chemical #)
Purpose: film grade
Feature remark: features: transparency, tension and good processability.
Important parameters: melt flow rate: 2 g/10min density: 0.923 g/cm3, notched impact strength: 150 tensile strength: 11 MPa, elongation at break: 480% VEKA softening point: 97 C embrittlement temperature: -76 C.
Manufacturer: Korea LG chemical company
LDPE (low density polyethylene LDPE /FB3500/LG chemical #)
Use: film grade
Feature notes: features: transparency and gloss
Important parameters: melt flow rate: 3.5 g/10min density: 0.924 g/cm3, notched impact strength: 100 tensile strength: 10 MPa, elongation at break: 400% VEKA softening point: 95 C embrittlement temperature: -76 C.
Manufacturer: Korea LG chemical company
LDPE (low density polyethylene LDPE /FB0500/LG chemical #)
Use: other
Characteristic notes: characteristics: crack resistance, heat shrinkage, good transparency
Important parameters: melt flow rate: 0.5 g/10min density: 0.921 g/cm3, notched impact strength: 300 tensile strength: 14 MPa, elongation at break: 600% VEKA softening point: 94 C embrittlement temperature: -76 C.
Manufacturer: Korea LG chemical company
LDPE (low density polyethylene LDPE /BB0305/LG chemical #)
Use: other
Characteristic notes: characteristics: Tortoise resistance, resistance to LV, and good impact resistance
Important parameters: melt flow rate: 0.3 g/10min density: 0.92 g/cm3, tensile strength: 17 MPa, elongation at break: 650% VEKA softening point: 95 C embrittlement temperature: -76 C.
Manufacturer: Korea LG chemical company
LDPE (low density polyethylene # LDPE) /5321UV/ Korea China
Purpose: film grade
Characteristic notes: characteristics: UV stability, machinability and excellent mechanical properties
Important parameters: melt flow rate: 3 g/10min density: 0.921 g/cm3, notched impact strength: 75 tensile strength: 11 MPa, elongation at break: 650% VEKA softening point: 88 degrees.
Manufacturer: Korea Hwa comprehensive chemical company
LDPE (low density polyethylene # high-pressure polyethylene) /D110/ Shanghai petrochemical
Use: other
Characteristic notes: polymer type: homopolymer method: extrusion
Important parameters: melt flow rate: 1.1 g/10min density: 0.92 g/cm3 tensile strength: 11.7 MPa
Manufacturer: Sinopec, Shanghai petrochemical Limited by Share Ltd
LDPE (low density polyethylene # high-pressure polyethylene) /J110/ Shanghai petrochemical
Use: other
Characteristic notes: polymer type: homopolymer method: extrusion
Important parameters: melt flow rate: 1.1 g/10min density: 0.92 g/cm3 tensile strength: 11.7 MPa
Manufacturer: Sinopec, Shanghai petrochemical Limited by Share Ltd
LDPE (low density polyethylene # LDPE) /1938Z300/ SABIC of Saudi Arabia
Use: other
Characteristic notes: high melting finger, low zero shear viscosity. Product trademark: SABIC
Important parameters: melt flow rate: 38 g/10min density: 0.919 g/cm3 VEKA softening point: 78 C
Manufacturer: Saudi Basic Industry Company
LDPE (low density polyethylene # LDPE) /1965Z300/ SABIC of Saudi Arabia
Use: other
Characteristic notes: high melting finger, low zero shear viscosity. Product trademark: SABIC
Important parameters: melt flow rate: 65 g/10min density: 0.919 g/cm3 VEKA softening point: 104 C
Manufacturer: Saudi Basic Industry Company
LDPE (low density polyethylene # LDPE) /2004TX33/ SABIC of Saudi Arabia
Purpose: film grade
Characteristic notes: good optical performance. Product trademark: SABIC
Important parameters: melt flow rate: 4.5 g/10min density: 0.921 g/cm3, notched impact strength: 15 tensile strength: 15 MPa, elongation at break: 500% VEKA softening point: 89 degrees.
Manufacturer: Saudi Basic Industry Company
LDPE (low density polyethylene # high-pressure polyethylene) /LDI-305YY/ Malaysia daito
Use: other
Characteristic notes: characteristics: good hardness, impact strength
Important parameters: melt flow rate: 6 g/10min density: 0.92 g/cm3, tensile strength: 10.6 MPa, elongation at break: 450% VEKA softening point: 87 DEG heat deformation temperature: -70 C.
Manufacturer: Malaysia daito company
LDPE (low density polyethylene # high-pressure polyethylene) /M015X/ Malaysia PETLIN
Use: other
Feature remark: additive: antioxidant
Important parameters: melt flow rate: 15 g/10min density: 0.92 g/cm3
Manufacturer: Malaysia PETLIN company
LDPE (low density polyethylene # LDPE) /F117-1/ Singapore polyolefin
Use: film grade
Important parameters: melt flow rate: 0.25 g/10min density: 0.923 g/cm3 tensile strength: 20 MPa fracture extension