使用方法：

FDJ-230手持式切割鋸可快速切割管道、電纜、角鋼、結構鋼、U型鋼、鏈條、錨桿、錨索等。

采用錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。

FDJ-230風動手持切割鋸是我公司針對高危，安全系數要求特別高的工作環境，如化工.治煉廠.天然氣開采.高危潮濕的隧道，水下及狹窄的空間作業，尤其是高瓦斯防爆礦井。山西萬澤錦達礦山機械設備有限公司自主研發的新型多用途風動手持切割工具。它使用臺灣進口氣動馬達作為動力輸出，利用壓縮空氣作為動力源，不用電源。風動手持切割鋸不但整機重量輕，操作簡單，攜帶方便零火花，提高工作效益。本產品安全可靠是高危行業的最理想氣動切割工具。

聯系人金經理電話13934240041

風動手持式切割鋸介紹

1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。

2、確保牢固固定了所需切割的材料，防止其移動。

3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。

4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。

5、關閉空氣馬達時，釋放閥桿。

6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。

7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。 源匯區FDJ-120/手提式切割鋸

8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。

9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。 我們不向客戶承諾不實際的理論，吹噓、夸大其詞。但能保證一直都在創新的道路上，因為市場給了我們答案，客戶給了我們認可。

FDJ-230型風動金屬切割鋸 無火花切割鋼材切割鋸

 額外風壓 0.4~0.6MPa

 額外功率 2.0 kW 

 額外轉速 3200r/min 

 額外轉矩 45N.

 鏈速     400mm /min 

 耗氣量   2.0M3 /min  

 機重     6kg

Introduction of pneumatic hand held cutting saw
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. Yuanhui District FDJ-120/ portable cutting saw
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. We don't promise unrealistic theories to customers, bragging, and exaggerating. But it can always be on the path of innovation, because the market gives us the answer, and the customer has given us approval.