“十年老店，完備售后，信譽信賴” 是專業塑膠原料供應商

本司貨源穩定充足，發貨準時，交期和質量均有保障！
根據客戶要求，可提供塑膠原料相關報告。如：ROHS(SGS)報告，UL認證，材質證明及物質安全資料表（MSDS）！

價格合理,誠信經營，可全國供貨（廣東省內 免費送貨上門）。

歡迎來電咨詢7*24全天候服務熱線：13686017791 易小姐 QQ：335171600

透明聚碳酸酯PC加玻纖塑料件加工注意問題

透明塑膠PC+gf產品由于透光率要高，所以PC+gf塑料制品表面質量的要求必須嚴格，不能有任何斑紋、氣孔、泛白、霧暈、黑點、變色、光澤不佳等缺陷，因而在整個注塑過程對原料、設備、模具、甚至產品的設計，都要十分注意和提出嚴格甚至特殊的要求。

另外，由于透明PC+gf塑料多為熔點高、流動性差，因此為保證產品的表面質量，往往需要較高的溫度，注射壓力、注射速度等工藝參數也要作細微調整，使注塑料時既能充滿模，又不會產生內應力而引起產品變形和開裂。

因此從原料準備，對設備和模具要求、注塑工藝和產品的原料處理幾方面都要進行嚴格的操作。

1.原料的準備與干燥

由于在PC+gf塑料中含有任何一點雜質，都可能影響產品的透明度，所以在儲存、運輸、加料過程中都必須注意密封，保證原料的干凈。

特別是原料中含有水分，加熱后會引起原料的變質，所以一定要做干燥處理。在注塑的時候，加料必須使用干燥的料斗。還要注意一點的是干燥的過程中，輸入的空氣最好應經過濾、除濕，以便保證不會污染原料。

2.機筒、螺桿及其附件的清潔

為防止PC+gf原料污染和在螺桿及附件凹陷處存有舊料或雜質，特別在熱穩定性差的樹脂存在，因此在使用前、停機后都應用螺桿清洗劑清洗干凈各件，使其不得粘有雜質，當沒有螺桿清洗劑時，可用PE、PS等樹脂清洗螺桿。

當臨時停機時，為防止原料在高溫下停留的時間過長，引起解降，應將干燥機和機筒溫度降低，如PC+gf、PMMA等機筒溫度都要降至160℃以下(料斗溫度對于PC應降至100℃以下)。

3.在模具設計上應注意的問題

為了防止出現原料回流動不暢，或冷卻不均造成塑料成型不良，產生表面的缺陷和變質，一般在模具設計時候，應該注意以下幾點：

壁厚應盡量均勻一致，脫模斜度要有足夠大;

過渡部分應圓滑，并逐步過渡，防止有尖角、銳邊產生，特別是PC+gf產品一定不要有缺口;

澆口、流道盡可能寬大、粗短，且應根據收縮冷凝過程設置澆口位置，必要時應加冷料井;

模具的表面應光潔，粗糙度低(最好低于0.8);

排氣孔。槽必須要足夠，以及時排出空氣和熔體中的氣體;

除PET外，壁厚不要太薄，一般不得小于lmm。

4.注塑工藝方面應該注意的問題

為了減少內應力和表面質量缺陷，在注塑工藝方面應注意以下幾方面的問題：

注射壓力：一般較高，以克服熔料粘度大的缺陷，但壓力太高會產生內應力造成脫模因難和變形;

注射速度：在滿足充模的情況下，一般宜低，最好能采用慢一快一慢多級注射;

保壓時間和成型周期：在滿足產品的充模，不產生凹陷、氣泡的情況下;宜盡量短，以盡量減低熔料在機筒停留的時間;

螺桿轉速和背壓：在滿足塑化質量的前提下，應該盡量低，為防止產生解降的可能;

模具溫度：制品的冷卻好壞，對質量影響極大，所以模溫一定要能精確控制其過程，有可能的話，模溫宜高一些好。

5.其他方面的問題

由于為了要防上表面質量惡化，一般注塑的時候應盡量少用脫模劑;當用回用料時不得大于20%。

對于除PET外，制品都應進行后處理，以消除內應力，PMMA應在70-80t熱風循環干燥4小時;PC應在清潔空氣、甘油、液體石臘等加熱110-135℃，時間按產品而定，最高需要10多小時。而PET必須經過雙向拉伸的工序，才能得到良好機械性能。

部分型號部分物性表

ABS (acrylonitrile / butadiene / styrene copolymer #) /P2M/ ABS
Use: other
Important parameters: melt flow rate: 18 g/10min density: 1.04 g/cm3 notch impact strength: 22 VEKA softening point: 97 C thermal deformation temperature: 93 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS E211/
Use: other
Important parameters: melt flow rate: 6 g/10min density: 1.05 g/cm3 notch impact strength: 22 VEKA softening point: 108 C thermal deformation temperature: 101 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H603/
Use: other
Important parameters: melt flow rate: 7 g/10min density: 1.04 g/cm3 notch impact strength: 28 VEKA softening point: 100 C thermal deformation temperature: 98 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H605/
Use: other
Important parameters: melt flow rate: 25 g/10min density: 1.05 g/cm3 notch impact strength: 17 VEKA softening point: 101 C thermal deformation temperature: 96 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H702/
Use: other
Important parameters: melt flow rate: 16 g/10min density: 1.04 g/cm3 notch impact strength: 16 VEKA softening point: 104 C thermal deformation temperature: 99 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H802/
Use: other
Important parameters: melt flow rate: 8 g/10min density: 1.05 g/cm3 notch impact strength: 15 VEKA softening point: 108 C thermal deformation temperature: 101 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H801/
Use: other
Important parameters: melt flow rate: 9 g/10min density: 1.07 g/cm3 notch impact strength: 30 VEKA softening point: 106 C thermal deformation temperature: 99 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS M203/
Use: other
Important parameters: melt flow rate: 31 g/10min density: 1.05 g/cm3 notch impact strength: 16 VEKA softening point: 97 C thermal deformation temperature: 94 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS M201/
Use: other
Important parameters: melt flow rate: 18 g/10min density: 1.05 g/cm3 notch impact strength: 19 VEKA softening point: 97 C thermal deformation temperature: 96 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS E401/
Use: other
Important parameters: melt flow rate: 5 g/10min density: 1.04 g/cm3 notch impact strength: 30 VEKA softening point: 99 C thermal deformation temperature: 94 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H604/
Use: other
Important parameters: melt flow rate: 8 g/10min density: 1.04 g/cm3 notch impact strength: 21 VEKA softening point: 101 C thermal deformation temperature: 98 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H701/
Use: other
Important parameters: melt flow rate: 9 g/10min density: 1.04 g/cm3 notch impact strength: 26 VEKA softening point: 104 C thermal deformation temperature: 100 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H803/
Use: other
Important parameters: melt flow rate: 6 g/10min density: 1.05 g/cm3 notch impact strength: 22 VEKA softening point: 108 C thermal deformation temperature: 101 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS M405/
Use: other
Important parameters: melt flow rate: 9 g/10min density: 1.02 g/cm3 notch impact strength: 29 VEKA softening point: 95 C thermal deformation temperature: 94 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS M501/
Use: other
Important parameters: melt flow rate: 8 g/10min density: 1.03 g/cm3 notch impact strength: 36 VEKA softening point: 95 C thermal deformation temperature: 95 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /5300/ ABS
Use: other
Important parameters: melt flow rate: 5 g/10min density: 1.07 g/cm3, molding shrinkage: 0.65% notched impact strength: 32 elongation at break: 15% flexural strength: 77 MPa, bending modulus: 2300 MPa hardness: 100 VEKA softening point: 106 DEG heat deformation temperature: 99 degrees C
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /556/ ABS
Use: other
Characteristic notes: low gloss and impact resistance
Important parameters: melt flow rate: 6 g/10min density: 1.06 g/cm3, notched impact strength: 107 tensile strength: 19.3 MPa flexural strength: 31 MPa bending modulus: 1450 MPa, hot deformation temperature: 80 degrees.
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /DP ABS H950/
Use: other
Important parameters: melt flow rate: 4.5 g/10min density: 1.05 g/cm3 notch impact strength: 16 VEKA softening point: 113 C thermal deformation temperature: 103 centigrade
Manufacturer: Ineos ABS company
ABS (acrylonitrile / butadiene / styrene copolymer #) /101/ Yuyao Yi Wei
Use: other
Feature notes: the high toughness ABS produced by our company has maintained the high rigidity, low shrinkage and good surface brightness of ABS raw materials. Meanwhile, a new ABS toughening agent has been adopted, which greatly improves the impact strength and makes ABS good.