FDJ-230煤礦鋼管切割鋸廠家

產品概述：

風動手持切割鋸是我公司針對高危，安全系數要求特別高的工作環境，如化工.治煉廠.天然氣開采.高危潮濕的隧道，水下及狹窄的空間作業，尤其是高瓦斯防爆礦井。

山西萬澤錦達礦山機械設備有限公司自主研發的新型多用途風動手持切割工具。它使用臺灣進口氣動馬達作為動力輸出，利用壓縮空氣作為動力源，不用電源。風動手持切割鋸不但整機重量輕，操作簡單，攜帶方便零火花，提高工作效益。本產品安全可靠是高危行業的氣動切割工具。

特點:
    適合鋸切各種鋼管、鋁型材、銅、鐵等金屬管材棒材。切斷面平整,精度高.
冷卻循環系統,使工件切面光潔準確，無毛邊,提高鋸片使用壽命,適合多量長時間鋸切。

產品技術參數：

品牌：萬澤錦達  

型號：FDJ-230 

類型：手用鋸條鋸片     

表面處理：半拋鍍鉻

全長：1350mm   

寬度：15mm     

齒距：0.2mm         

厚度：0.1mm      

鋸路寬：1200mm

為了安全作業需要注意以下幾點：
1、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命
2、關閉空氣馬達時，釋放閥桿。

3、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。

4、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。

5、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。

6、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。

7、確保牢固固定了所需切割的材料，防止其移動。

8、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。

9、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減Product overview:
Pneumatic hand cutting saw is my company for high risk, safety factor particularly demanding work environment, such as chemical. Refinery. Natural gas mining. High risk wet underwater tunnel, and narrow space operations, especially in high gas coal mine explosion.
Shanxi million of new multi Zejin pneumatic mining machinery and equipment limited company independent research and development of hand-held cutting tools. It uses Taiwan imported pneumatic motor as power output, uses compressed air as power source, and does not use power. The pneumatic handheld cutting saw is not only light in weight, simple in operation and convenient to carry zero spark, but also to improve work efficiency. This product is safe and reliable. It is a pneumatic cutting tool in high risk industry.
Characteristic:
It is suitable for cutting all kinds of steel pipe, aluminum, copper, iron and other metal pipe rod. The cutting section is smooth and the precision is high.
The cooling cycle system makes the cutting surface of the workpiece accurate and accurate, without edge, and improves the service life of the saw blade, and is suitable for a long time sawing.
Product technical parameters:
Brand: up to Zejin million
Model: FDJ-120
Type: hand saw blade
Surface treatment: semi cast chromium plating
Full length: 1350mm
Width: 15mm
Tooth distance: 0.2mm
Thickness: 0.1mm
Sawing width: 1200mm
In order to work safely, we need to pay attention to the following points:
1, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life
2. When the air motor is closed, the stem is released.
3. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
4, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
5. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
6, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
7, ensure that the required cutting material is firmly fixed to prevent its movement.
8. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
9. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.