商品介紹：
·FDJ-230型風動切開鋸適用于風險的作業環境，可在較高溫的環境下作業，無火花，在濕潤的環境中無漏電風險，是一款功能牢靠、安全型及效率極高的抱負風動東西之一。廣泛用于采礦、石化、修建等職業。
·使用井下壓風管道體系作為動力源。重量輕，易帶著；構造科學，便于作業。 民權縣多功能//氣動風動切割鋸
·可迅速切開管道、電纜、角鋼、構造鋼、U型鋼、鏈條、錨桿、錨索等。
·錮金屬鋼合金超級鋸條，耐高溫、耐沖突、運用壽數長。十分適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。
現如今冷切割的方式有以下幾種：鋸切割、線切割、超高壓水切割、激光切割等。
FDJ-230手持式氣動切割機礦用風動切割鋸
萬澤錦達冷切割工具的優勢： 我們的風動切割機優勢：無火花冷切割。尺寸準確；切口平整，無裂紋、重皮、毛刺、凹凸、縮口、熔渣、氧化物、鐵屑等；快速省里。切口端面與管子軸心線要垂直，傾斜偏差Δ≤管子外徑的1%，且≤3mm。PE管無變形。經濟效益高，更便捷。
礦用風動切割鋸，又稱氣動切鐵鋸，礦用風動鋸軌機，礦用無火花切割鋸，礦用軌道鋼切割鋸，礦用U型鋼切割機，礦用管道切割鋸，手持式無火花切割機，小型防爆切割鋸等等，（根據其用法不同名稱也不盡相同）。
技術參數：

類型	功率	耗氣量	切開厚度	切開寬度（直徑）	鋸片速度	重量
FDJ-120	0.5kw	0.6m3/min	三種鋸片： 0—30mm 30—50mm 50—120mm	120mm	60m/min	6kg
FDJ-180	1.0kw	1.2m3/min		180mm	90m/min	10kg
FDJ-230	1.5kw	1.5m3/min		230mm	120m/min	16kg

氣動風動切開鋸運用方法：
1、知道所需切開的材料，如有必要可以通過降低空氣壓力來降低鋸片的改變速度。 新華區FDJ-230/型風動切割鋸
2、確保健壯固定了所需切開的材料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后初步切開。
4、用鋸的重量來控制切開壓力。對于較軟的材料來說，這么的重量現已滿意。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方法來降低鋸片的改變速度。切開是堅持鋸筆直。鋸片的任何曲解或歪斜都可以降低其運用壽數。（留意：避開切開后可以墜落的碎片。切開即將結束時，切勿使鋸碰到您的身體、工件或鄰近的其它人員。）
5、封閉空氣馬達時，開釋閥桿。
6、下次切開初步前，鋸片有必要堅持運動情況。氣動鋸時，鋸片不能接觸任何表面。 太康縣石油管道/風動防爆切割鋸
7、斷開空氣軟管時，封閉空氣軟管閥。斷開前，先翻開空氣閥給軟管減壓。
8、更換鋸片前，有必要斷開空氣軟管，并推動閥桿以開釋掉馬達內的壓力。
9、順時針改變調整手柄以便開釋鋸片導桿上的張力。然后開釋側面板的鎖以便翻開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
留意事項：
一切動力東西都也許會十分風險。請遵循下列安全過程以便維護自己。
1、戴上護目鏡、手套、安全靴和具有防護作用的廠服。
2、時間堅持腳下安穩、平衡。 經濟開發區萬澤錦達/風動氣動切割鋸
3、醫療治療、喝酒或服食藥物后請勿操作本東西。
4、放置機器前，先關掉機器（封閉閥門）。
5、機器停止作業后，應立即切斷氣源供給，防止在無意識下發動機器。
6、請勿站在梯子上或靠在腳手架上操作本機。非必要作業人員請遠離作業區。
7、操作發動東西鉗，應先移除發動軟管。關掉主氣閥。要開釋緊縮氣體，則從頭翻開手閥門。

Commodity introduction:
The FDJ-120 type pneumatic cutting saw is suitable for the risk working environment. It can operate in a high temperature environment, no sparks, and no leakage risk in humid environment. It is a reliable, safe and highly efficient aspiration pneumatic thing. It is widely used in mining, petrochemical, construction and other professions.
Use the downhole air pressure pipe system as a power source. The weight is light and easy to be carried; it is scientific and easy to work. Minquanxian multifunctional pneumatic pneumatic / cutting saw
The pipeline, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on can be cut off quickly.
Super - Han metal steel alloy saw blade, high temperature resistance, long life, the use of conflict. It is very suitable for sawing stainless steel, nickel base alloy, iron, copper, aluminum, glass, plastic, wood and so on.
There are several ways of cold cutting now: saw cutting, wire cutting, ultra high pressure water cutting, laser cutting and so on.
FDJ-120 hand-held pneumatic cutting machine mine pneumatic cutting saw
000 Zejin up to cold cutting tools our advantages: pneumatic cutting machine advantages: no spark of cold cutting. Accurate size; smooth incision, no crack, heavy skin, burr, concave and convex, shrinkage, slag, oxide, iron and so on; fast province. Cut face and pipe axis deviation is less than or equal to the vertical, inclined delta pipe diameter 1%, and less than 3mm. PE pipe deformation. The economic benefit is high and more convenient.
Mine pneumatic cutting saw, also known as pneumatic cutting saws, mine pneumatic rail sawing machine, mine non spark cutting saw, mining track steel cutting saw, mine U type steel cutting machine, mining pipe cutting saw, hand-held non spark cutting machine, small explosion-proof cutting saw, according to its usage (different names are not the same).
Technical parameters:
Type of type power consumption cut width cut width (diameter) speed weight of saw blade
FDJ-120 0.5KW 0.6m3/min three saws:
0 - 30mm
30 - 50mm
50 - 120mm 120mm 60m/min 6kg
FDJ-180 1.0kw 1.2m3/min 180mm 90m/min 10kg
FDJ-230 1.5kw 1.5m3/min 230mm 120m/min 16KG

Pneumatic pneumatic cut saw application method:
1. Knowing the material that needs to be cut, it is necessary to reduce the speed of the saw blade by reducing the pressure of the air. Xinhua District of FDJ-120/ pneumatic cutting saw
2. It is true that the health-care stout has fixed the required cut materials to prevent it from moving.
3. When pneumatic air motor, press the stem with the finger, and then cut it initially.
4, the cutting pressure is controlled by the weight of the saw. This weight is now satisfactory for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of the saw blade can be reduced by pressure.  The incision is to keep the saws straight. Saw any distortion or skew can reduce the use of life. (notice: avoid debris that can fall after a cut. When the cut is about to end, do not make the saw touch your body, the workpiece, or the other people in the neighborhood.
5. When the air motor is closed, the stem is released.
6. Before the next incision, it is necessary to adhere to the movement of the saw blade. The saw blade can't contact any surface when a pneumatic saw. County of Taikang oil pipeline explosion / pneumatic cutting saw
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Note:
All power things may be very risky. Please follow the following safety procedures in order to maintain yourself.
1, wear goggles, gloves, safety boots and protective clothing.
2, time to adhere to the feet of stability, balance. 000 Zejin Economic Development Zone of pneumatic pneumatic cutting saw
3, medical treatment, alcohol or drugs do not operate the things.
4. Before placing the machine, turn off the machine first (closed valve).
5. After the machine stops working, the supply of gas should be cut off immediately to prevent the machine from launching under the unconsciousness.
6. Do not stand on the ladder or operate on the scaffolding. Please stay away from the operation area.
7, operation to launch a clamp, should first remove the hose. Turn off the main valve. To release the compressed gas, then turned away from the valve.