只一個優點就能讓您選擇我們的氣動線鋸，更何況我有那么多的優點讓您選擇我們的氣動線鋸，您一定會心動的。
優點一：氣動線鋸用途多
氣動帶鋸主要用于刮板運輸機鏈條切割，支護材料切割，金屬錨桿切割，工作面搶險救援。通過采用不同鋸條規格，可以切割從合金鋼材到橡膠、原木、木制品、塑料等各種材料。
優點二：氣動線鋸使用范圍廣
1.氣動鋼材鋸無需擔心火花帶來的危險，所以適用于煤礦及化工等危險環境作業，廣泛用于切割大直徑管道、槽鋼、鋼絲線纜等金屬，非金屬切割。
2.無火花切割鋸，可在高溫下、潮濕環境中作業無漏電危險。
3.氣動防爆鋸，結構緊湊，牢固可靠、重量輕便 攜帶方便，一人僅可操作，降低工人的勞動強度，提高工作效率。
優點三：氣動線鋸發貨清單
1.主機一套
2.鋸條1根
3.合格證一份
4.使用說明書一份
優點四：氣動線鋸特點突出
1、氣動線鋸采用井下壓縮空氣作為工作介質，適用于掘進或采煤工作面各種工作環境；
2、手持式氣動線鋸結構強度高，耐沖擊，適應井下惡劣工作環境；
3、無火花氣動線鋸專利風冷結構和轉速設計避免了切割過程火花的產生
4、防爆氣動線鋸在井下爆炸危險環境中使用時可使用外注水或者乳化液對鋸條進行冷卻，提高使用壽命，同時消除火花隱患；
5、往復氣動線鋸采用循環式鋸條進行切割，切割速度快，切割尺寸范圍大；陜北基地石材石板汽油切割鋸
6、安全氣動線鋸切割直徑較大材料或連續作業時間較長可以采用專用支架支撐，大大降低勞動強度，提高工作的安全性。
7、小型氣動線鋸體積小，重量輕，便于井下移動。
優點五：氣動線鋸參數完美
技術參數：
型號 功率 耗氣量 切割厚度 切割寬度（直徑） 鋸片速度 重量
FDJ-120 0.5kw 0.6m3/mi 三種鋸片： 0—30mm 30—50mm 50—120mm 120mm 60m/mi 6kg
FDJ-180 1.0kw 1.2m3/mi 180mm 90m/mi 10kg
FDJ-230 1.5kw 1.5m3/mi 230mm 120m/mi 16kg
使用須知：
1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。
2、確保牢固固定了所需切割的材料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。
4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
5、關閉空氣馬達時，釋放閥桿。
6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。
8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。
9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。
特點優勢：
礦用軌道輕型3分鐘軌道重型5分鐘
1.90°直切,45°斜切,立式切割一體機。
2.運轉速度只有砂輪機的1/60,安全無火花。
3.切縫窄0.5mm,切割表面平整，精度高，無掛渣，無脫碳。
4.鋸條使用壽命長，單位切割成本低，一根鋸條使用壽命等同于50-80片砂輪切割片，較電能鋸節能60%
注意事項：
所有動力工具都可能會非常危險。請遵循下列安全步驟以便保護自己。
1、戴上護目鏡、手套、安全靴和具有防護作用的工作服。
2、時刻保持腳下穩定、平衡。
3、醫療治療、飲酒或服食藥物后請勿操作本工具。
4、擱置機器前，先關掉機器（關閉閥門）。
5、機器停止工作后，應立即切斷氣源供應，避免在無意識下啟動機器。
不奪桂冠誓不回，那怕銷得人憔悴。 求真尚美，礪志篤行。 6、請勿站在梯子上或靠在腳手架上操作本機。非必要工作人員請遠離工作區。
7、操作啟動工具鉗，應先移除啟動軟管。關掉主氣閥。要釋放壓縮氣體，則重新打開手閥門。
8、雙手緊握機器。保持雙手和身體的其它部分遠離切割區。
9、運送機器前務必關掉馬達并切斷氣源。
10、注意可能掉落的碎片。
Only one advantage can let you choose to move our wire gas, and I have so many advantages to let you choose our gas moving wire, you will be moved.
One advantage: pneumatic wire use
The pneumatic band saw is mainly used in the chain cutting of the scraper conveyor, the cutting of the supporting materials, the cutting of metal bolt, and the rescue and rescue of the working face. It can be cut from alloy steel to rubber, log, wood products, plastic and other materials through the use of different sawbar specifications.
Two advantages: the use of a wide range of pneumatic wire
1., pneumatic steel saws need not worry about the danger brought by sparks, so they are suitable for dangerous environment operations such as coal mines and chemical industries. They are widely used for cutting large diameter pipes, channel steel, wire and cable metals, and non-metal cutting.
2. no spark cutting saw can work without leakage at high temperature and humid environment.
The 3. pneumatic explosion-proof saw has compact structure, strong reliability, light weight and convenient portability. Only one person can operate, reduce labor intensity and improve work efficiency.
Three advantages: pneumatic wire delivery list
A set of 1. hosts
2. saws 1
3. certificate of qualification
4. a copy of the instructions
Four advantages: pneumatic wire features
1, pneumatic wire by the compressed air as working medium, suitable for driving or working faces of various working environment;
2, a hand-held pneumatic wire structure of high strength, impact resistance, adapt to the harsh working environment of underground;
3, no spark wire pneumatic air cooling structure and speed of design patent avoids cutting spark
4, explosion-proof pneumatic wire used in underground explosion hazardous environment can be carried out on the use of external water cooling blade or emulsion, improve the service life, and eliminate the hidden trouble of spark;
5, reciprocating pneumatic wire by using cyclic saw blade cutting, cutting speed, cutting size range; Shaanxi base stone stone cutting saw gasoline
6, pneumatic wire cutting large diameter material or continuous long work time can be supported by special support, greatly reduce the labor intensity, improve work safety.
7, small pneumatic wire has the advantages of small size, light weight, easy to move underground.
Five advantages: pneumatic wire parameters perfect
Technical parameters:
Model power consumption gas cutting thickness cutting width (diameter) saw blade speed weight
FDJ-120 0.5KW 0.6m3/mi three saw blades: 0 - 30mm 30 - 50mm 50 - 120mm 120mm 60m/mi 6kg
FDJ-180 1.0kw 1.2m3/mi 180mm 90m/mi 10kg
FDJ-230 1.5kw 1.5m3/mi 230mm 120m/mi 16KG
Use of instructions:
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel.
Characteristic advantage:
Mined track light 3 minute track heavy 5 minutes
1.90 degrees 45 degrees straight, oblique, vertical cutting machine.
2. running speed is only 1/60 of sand turbine, safe and free of spark.
The 3. slit is narrow 0.5mm, the cutting surface is smooth, the precision is high, no slag and no decarburization.
The 4. saw blade has long service life, low cost of cutting, and the service life of a sawing is equal to 50-80 pieces of grinding wheel, and the electric energy sawing is 60% energy saving.
Matters needing attention：
All power tools can be very dangerous. Please follow the following safety steps to protect yourself.
1, wear goggles, gloves, safety boots and protective work clothes.
2, keep steady and balance at the moment.
3, medical treatment, alcohol or drugs do not operate the tool.
4. Before setting up the machine, turn off the machine first (turn off the valve).
5. After the machine stops working, the gas supply should be cut off immediately to avoid starting the machine under the unconsciousness.
Do not take the crown oath not to return, that is afraid to sell people haggard. The truth is beauty, Li Zhi dusing. 6. Do not stand on the ladder or operate on the scaffolding. Unnecessary staff please stay away from the workspace.
7. To start the tool tongs, the starting hose should be removed first. Turn off the main valve. To release the compressed gas, reopen the hand valve.
8, hold the machine with both hands. Keep the rest of your hands and body away from the cutting area.
9. Be sure to turn off the motor and cut off the gas source before transporting the machine.
10, pay attention to the debris that may fall.
在線客服：0571-87774297
