天津掛歷全自動YO單/雙線圈裝訂機廠家電話價格報價

天津市 和平區  北辰區  河北區  河西區  西青區  津南區  東麗區  武清區  寶坻區  紅橋區  大港區  漢沽區  靜海縣  寧河縣  塘沽區  薊縣  南開區  河?xùn)|區

機器出廠前已裝有調試好的一套模具。當機器需要更換模具時，可按照以下步驟進行。The machine is shipped with a good set of molds. When the machine needs to replace the mold, follow the steps below.
5.1  臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機穿線 Inserting the wire
將線穿入進線組件，經過過線輪24.1，潤滑盒25，過線輪24.2,計數輪26（經過計數輪時將線繞計數輪一圈），過線輪24.3,再經過鐵線整直板(如圖一)，之后在芯棒上.

5.2調試 臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機芯棒 Mandrill adjustment
5.2.1要成形不同大小的線圈,須選用相應的線圈芯棒,選定適合的芯棒后,先將芯棒插入主軸并從主軸的另一端用螺絲鎖緊,開機運轉時,芯棒應與主軸同心.

Chose suitable mandrill according to different coil size. After install the mandrill onto the main axis with tighten screws, the mandrill should be the same concentric of the main axis when the machine is running.

5.2.2 臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機上有三個插針板,作用是固定線圈的齒距.插針板須定在對應的插針板座上,從前方向下編號順序?yàn)?,2,3.

There are three pieces of pin stands. Order number 1,2,3 from the front to the lower one. Pins are fixed onto the stands for supporting the teeth pitch.
5.2.3把 臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機插針插入插針板上,注意針端與芯棒面須有0.05-0.15的間隙(工具箱配有塞尺).間隙過大,線材表面會刮花,如針端與芯棒配合過緊,則會刮花芯棒表面,造成坑槽,容易卡線和刮花線材.

When install the pins please keep the gap between 0.05-0.15mm (tool box has feeler gauge). Once the gap too big the wire material easy get scratched. The mandrill could be scratched the surface if the pins too closed. The mandrill the slot caused and could be damage the wire materials, too.