塑料滑動摩擦磨損試驗儀 微機控制

產品型號：  M-200 ：塑料摩擦，橡膠摩擦  用途：絕緣材料摩擦系數。

塑料滑動摩擦磨損試驗儀 微機控制
特點：
適用于塑料制品及橡膠制品或其他復合材料的滑動摩擦，摩損性能測試。也可對試驗中試樣的摩擦力、摩擦系數和摩損量進行測定。
  M-200塑料滑動摩擦磨損試驗儀-液晶的詳細資料：
 
塑料滑動摩擦磨損試驗儀 微機控制
一、制造標準：
         GB3960 塑料滑動摩擦磨損試驗方法
產品名稱：塑料滑動摩擦磨損試驗儀
產品型號：M-200
顯示方式：液晶顯示
一、塑料滑動摩擦磨損試驗儀 微機控制
主要適用范圍及功能
本儀器是按照GB3960設計并制造。適用于塑料制品及橡膠制品或其他復合材料的滑動摩擦，摩損性能測試。也可對試驗中試樣的摩擦力、摩擦系數和摩損量進行測定。本機采用16位單片機電子處理系統，使得本儀器各項測試指標精度非常高。由于集成程度很高，所以設備本身的穩定性極好，本機具有一次設置，全自動運行，實驗結束后自動停機，并檢測摩損程度。是各個科研單位，大學，企業實驗室的必備檢測設備。
二、塑料滑動摩擦磨損試驗儀 微機控制
功能特點：
1、試樣尺寸： 30mm*7mm*6mm±0.1 mm
　  2、轉動速度： 0-200轉/分 連續可調
　  3、負 荷： 196N ± 0.2%(可擴充到392N)
　  4、摩擦環尺寸：￠40×10mm 倒角0.5×45°外圓表面與內圓同心度偏差小于0.01
　  5、摩擦力矩： 0--4N?m ±0.5%
　  6、計 數 器： 0-9999小時
    7、砝碼重量：4KG砝碼一件，1KG砝碼4件，可實現重量疊加功能。
三、塑料滑動摩擦磨損試驗儀 微機控制
精度：
     1、速度精度：1%
     2、負荷精度：0.5%
     3、摩擦力矩精度：1%
     4、計數器精度：1S
     5、傳感器測量精度：1% FS
 
四、塑料滑動摩擦磨損試驗儀 微機控制
主要配置：
1、主機一臺
      2、高精度扭矩傳感器一只
      3、彩晶顯示控制系統箱一臺
      4、4Kg砝碼兩件(備用一套)
      5、標準磨擦環四件(備用兩件)
      6、臺式微型打印機一臺
      7、產品使用說明書一份
      8、產品合格證
      9、產品裝箱單一份
      10、整機重量：約45公斤
Plastic sliding friction and wear tester controlled by Microcomputer
Product type: M-200: plastic friction, rubber friction uses: insulation material friction coefficient.
Plastic sliding friction and wear tester controlled by Microcomputer
Characteristic.
Applied to plastics and rubber products or other composite sliding friction, abrasion performance test. Can also be used to test sample, the friction coefficient of friction and abrasion quantity is measured.
M-200 plastic sliding friction and wear tester - crystal details:
Plastic sliding friction and wear tester controlled by Microcomputer
Manufacturing standards:
GB3960 test method for friction and wear
Product Name: plastic sliding friction and wear tester
Product type: M-200
Display: LCD
A friction and wear tester, microcomputer control
Main applicable range and function
The apparatus is designed and manufactured in accordance with GB3960. Applied to plastics and rubber products or other composite sliding friction, abrasion performance test. Can also be used to test sample, the friction coefficient of friction and abrasion quantity is measured. This machine uses 16 bit single chip electronic processing system, making the instrument each test indicator accuracy is very high. Since the integration degree is high, so the equipment itself excellent stability, this machine has a set, automatic operation, after the end of the experiment of automatic shutdown, and detecting the abrasion degree. Various research institutes, University, enterprise necessary laboratory testing equipment.
Two friction and wear tester, microcomputer control
Function characteristics:
In 1, the sample size: 30mm*7mm*6mm ±0.1 mm
2, rotation speed of 0-200 RPM: continuously adjustable
3, load: 196N ± 0.2% ( can be expanded to 392N )
In 4, the friction ring size: - 40 × 10mm chamfer of 0.5 x 45 degrees external round surface and inner circle concentricity deviation is less than 0.01
In 5, the friction torque: 0--4N ?m ± 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, can realize the function of the weight stack.
Three friction and wear tester, microcomputer control
Precision:
1, speed accuracy: 1%
2, load precision: 0.5%
In 3, the friction torque precision: 1%
4, counter accuracy: 1S
In 5, the sensor measurement precision: 1% FS
Four friction and wear tester, microcomputer control
Main configuration:
In 1, a mainframe
2, a high precision torque sensor
3, color crystal display control system box
In 4, 4Kg weight two ( reserve a set)
In 5, the standard friction ring four ( reserve two )
6, desktop mini printer
7, product using a manual
8, product certification
9, product packing list
In 10, the whole machine weight: about 45 kg