SB68固體體積電阻率及表面電阻率測試儀是根據GB/T 1410-2006《固體絕緣材料體積電阻率和表面電阻率試驗方法》(等同IEC 60093)和GB/T 10064-2006《測量固體絕緣材料絕緣電阻的實驗方法》(等同IEC 60167)而設計和制造的。集高阻和微電流功能為一體的測量儀器。主要用于各種絕緣材料的體積電阻率、表面電阻率和絕緣電阻及微電流的測量。

一、體積電阻率表面電阻率測定儀概述
本儀器是既可測量高電阻，又可測微電流。采用了美國Intel公司的大規模集成電路以及專利技術,使儀器體積小、重量輕、準確度高。以雙3.1/2 位數字直接顯示電阻的高阻計和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍最寬，準確度最高的數字超高阻測量儀。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓為10/50/100/250/500/1000V任意可調。本儀器具有精度高、顯示迅速、性好穩定、讀數方便， 適用于防靜電產品如防靜電鞋、防靜電塑料橡膠制品、計算機房防靜電活動地板等電阻值的檢驗以及絕緣材料和電子電器產品的絕緣電阻測量。本儀器除能測電阻外，還能直接測量微弱電流。
本儀器完全符合并優于國家標準GB1410《固體電工絕緣材料絕緣電阻、體積電阻系數和表面電阻試驗方法》和美國標準ASTM D257《絕緣材料的直流電阻或電導試驗方法》等標準的要求。本儀器是既可測量高電阻，又可測微電流。采用了美國Intel公司的大規模集成電路以及專利技術,使儀器體積小、重量輕、準確度高。以雙3.1/2 位數字直接顯示電阻的高阻計和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍最寬，準確度最高的數字超高阻測量儀。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓為10/50/100/250/500/1000V任意可調。本儀器具有精度高、顯示迅速、性好穩定、讀數方便， 適用于防靜電產品如防靜電鞋、防靜電塑料橡膠制品、計算機房防靜電活動地板等電阻值的檢驗以及絕緣材料和電子電器產品的絕緣電阻測量。本儀器除能測電阻外，還能直接測量微弱電流。
 

二、使用說明
（一）SB36應滿足下例要求：
1、測試電壓范圍應包括：100V~500V
2、SB36測量范圍應包括：1×106Ω~1×1017Ω
3、阻值大于1012Ω時，測量誤差應小于±20%，阻值不大于1012Ω時，測量誤差應小于±10%。
4、輸入接線的絕緣電阻應大于儀器輸入電阻的100倍。
5、測試時試樣及測量導線應有良好。
6、儀器應定期進行校驗。
（二）準備工作：
1、取被測液體（如：增塑劑）試樣50ml。
2、試樣應在溫度23±2℃，相對濕度65±5%的條件下處理2小時以上。
（三）測試步驟：
1、測試溫度23±2℃，相對濕度65±5%，無外界電磁場干擾環境中進行。
2、測試時對試樣所加電壓為100V~500V的直流電壓，選擇電壓檔次。
3、將試樣倒入高壓電極內，使液面剛好和環電極下緣全部接觸為止。
4、將充分放電后的試樣和電極，按SB36型固體（液體）體積及表面電阻率測試儀要求接線。
  外電極（高壓電極）接高固體（液體）體積及表面電阻率測試儀的高壓輸出端。
  內電極（測量電極）接固體（液體）體積及表面電阻率測試儀的測量端。
  中電極（環電極）接固體（液體）體積及表面電阻率測試儀的接地端。
5、儀器預熱30分鐘，穩定后調整儀器（調零），加上試驗1分鐘，讀取電阻指示值，然后放電1分鐘，再測試一次，以?二次的算術平均值作為試驗樣品電阻指示值。
（四）計算方法：
按式（1）計算體積電阻系數（pv）,計算結果取二位有效數字。
（五）注意事項：
1、測定電極必須放置在高絕緣的墊板上。
2、測定電極在測試前后，均應做好清洗工作，特別是三只電極的支撐件不得受到試樣的污染。

三、注意事項
1儀器操作前請您仔細閱讀使用說明書，規范操作。
2輕拿輕放，避免儀器震動，水平放置，垂直測量。
3儀器不使用時請切斷電源，連接線無需經常拔下，避免灰塵進入航空插頭引起短接等現象。
4探針筆測試結束，套好護套，避免人為斷針。

四、體積電阻率表面電阻率測試儀主要特點
電阻測量范圍寬 0.01×104Ω ～1×1018 Ω
電流測量范圍為 2×10-4Ａ ～1×10-16Ａ
體積小、重量輕、準確度高
電阻、電流雙顯示
性能好穩定、讀數方便
所有測試電壓(10/50/100/250/500/1000V) 測試時電阻結果直讀，免去老式高阻計在不同測試電壓下或不同量程時要乘以系數等使用不便的麻煩，    使測量超高電阻就如用萬用表測量普通電阻樣簡便。
既能測超高電阻又能測微電流
適用范圍廣:適用于防靜電產品如防靜電鞋、防靜電塑料橡膠制品、計算機房防靜電活動地板等電阻值的檢驗和電子電器產品的絕緣電阻測量

五、體積電阻率表面電阻率測試儀技術指標                                                                                                                                               
1.電阻測量范圍： 0.01×104Ω ～1×1018Ω。
2.電流測量范圍為: 2×10-4A～1×10-16A
3. 雙表頭顯示: 3.1/2位LED顯示
4. 內置測試電壓： 10V、50V、100V、250、500、1000V
5. 基本準確度：1% (*注)
6 使用環境: 溫度：0℃～40℃，相對濕度<80%
7 機內測試電壓: 10/50/100/250/500/1000V 任意切換    

                                  北京北廣咨詢電話 ： 010-52869521                 手機： 劉東旭  （銷售部經理）15011102183                                                                                                                                                                                                                                                                                                                                                                       

北京北廣精儀儀器有限公司是從事專業測量儀器以及相關設備的研發、生產、銷售、于一體是高新科技股份企業，并按照現代化經營管理實現企業化經營管理模式走向股份制正規
化企業，公司經過長期發展，現已擁有獨立的研發隊伍并已有海內外專家入注進行產品的研發與設計。

北廣公司保持以發展與中國測試產業相適應的應用技術為主線，通過與產業界協調發展的方式提高本公司的競爭實力和技術含量。

公司擁有一支優秀的技術團隊，并秉成“創新、精準、高效、跨越”的文化理念逐步打造成為一流的儀器檢測公司。 同時北廣公司強大的售后隊伍會對消費者進行全程的
優質服務， 以確保您的全程無憂！

中國檢測行業與驗證服務的尖端者和智領者，幫助眾多檢測質檢單位和學校教研單位提供一站式的全面質量解決方案。

我公司現有技術人員50人其中 專業研發人員占%15專業技術人員占%25 專業售后人員占%30

                            北廣精儀儀器設備有限公司的經營理念：

   一、誠信待戶 顧客至上      全心全意為顧客考慮，使顧客能切身感受到人性化的儀器。
 

  二、精準檢測 保質保量      精準檢測是我們的責任 保質保量是我們對客戶的鄭重承諾

  三、技術領先 創新理念   儲備一流的開發人才，引進世界領先技術，采用先進的設計理念，打造最精良的檢測儀器。

 
北廣產品廣泛應用于國防、大專院校以及檢測所等行業，本公司以技術的創新為企業的發展方向，以新型實用的產品引導客戶的需求

北廣精儀公司以精湛的技術、創新的理念、優質的產品獲得廣大業界的認可，產品在全國范圍內廣泛銷售，獲得廣大消費者的青睞。

 
北廣公司所供產品嚴格按照國家標準生產制造，嚴謹?shù)闹圃飙h(huán)節確保每一臺出廠儀器質量和性能的卓越，服務優質，質優價廉。

        注重每一個細節是北廣公司對于每個客戶的承諾 ， 也是北廣公司一直追求的宗旨。

       
                          以信譽  營客戶     以質量  鑄市場    以技術  保精準   以售后 造未來

                                                專業、技術、精準、高跨 

北廣公司其它絕緣材料檢測儀器:

BDJC-0-100KV 介電擊穿試驗儀

BDJC系列絕緣材料工頻率介電擊穿試驗儀

BDJC系列電壓介電強度試驗儀器

BDJC系列 電壓擊穿試驗儀

BDJC系列絕緣漆漆膜擊穿強度試驗儀

BDJC電容器紙工頻電壓擊穿試驗儀

EST-121 體積表面電阻率測定儀

GDAT-A介質損耗測試儀/介電常數測試儀

GDAT-C新型介電常數介質損耗測試儀

BDH 耐漏電起痕試驗儀

BDH-B耐電弧試驗儀

                                                       北京北廣咨詢電話 ： 010-52869521        手機： 劉東旭  （銷售部經理）15011102183
olume resistivity of surface resistivity tester
Digital high resistance, a current measuring instrument type: EST-121: volume resistivity, surface resistivity uses: Instrumentation Test
One, volume resistivity surface resistivity tester overview
This instrument can measure high resistance, and measuring current. The American company Intel large scale integrated circuit and patented technology, the instrument has the advantages of small volume, light weight, high accuracy. Dual 3.1/2 digital display the resistance high resistance meter and current. Limit from 1× 104 Ω～ 1× 1018 Ω, is currently the most wide measurement range, the most accurate digital ultra high resistance meter. Current measurement range of 2× 10-4 ～ 1× 10-16A. The built-in test voltage is 10/50/100/250/500/1000V adjustable. The instrument has the advantages of high precision, good stability, showing a rapid, easy reading, applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as the resistance value of the test as well as insulating materials electrical and electronic products insulation resistance measurement. The instrument can measure the resistance, and can directly measure the weak current.
Instrument is fully consistent with and better than the national standard GB1410 " solid electrical insulating materials, insulation resistance, volume resistivity and surface resistance test method " and " American Standard ASTM D257 DC resistance or conductance of insulating materials test methods " and other standards.
Two, volume resistivity surface resistivity tester main features
Resistance measuring range 0.01× 104 Ω～ 1× 1018 Ω
Current measurement range of 2× 10-4A ～ 1× 10-16A
Small volume, light weight, high accuracy
Resistance, current double display
Good performance is stable, easy reading
All the test voltage ( 10/50/100/250/500/1000V ) test resistance results in reading, is removed from the old high resistance meter in different test voltage or different scale should be multiplied by the coefficient of the inconvenient trouble, allowing the measurement of high resistance as the multimeter is used to measure the general resistance of samples is simple.
Not only can measure high resistance and micro current
Wide application: applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as resistance testing electrical and electronic products insulation resistance measurement
Three, volume resistivity surface resistivity tester technical indicators
The 1 resistor measurement range: 0.01× 104 Ω～ 1× 1018 Ω.
The 2 current measurement range : 2 × 10-4A～ 1 × 10-16A
3 double header display: 3.1/2 LED display
4 built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V
5 basic accuracy: 1% ( note )
6: use environment temperature: 0℃ ~ 40 ℃, relative humidity <80%
7 built-in test voltage: 10/50/100/250/500/1000V arbitrary switching
The 8 power supply forms: AC 220V, 50HZ, power consumption is about 5W
Four, volume resistivity surface resistivity meter working principle
According to the Ohm's law, the measured resistance is equal to voltage is applied through Rx V divided by the current I. The traditional high resistance meter is the working principle of measuring voltage V fixed, by measuring the current flows through the sampling resistor I to get the value of resistance. From Ohm's law can be seen, because the current I is inversely proportional to the resistance, but not proportional to the resistance, so the display value is nonlinear, namely the resistance to infinity, the current is zero, i.e., zero is∞, in the vicinity of the scale is very dense, with a low resolution. The scale is nonlinear. Because the measurement of different resistance, the voltage V also vary, so the average high resistance meter is poor accuracy, low resolution.
At the same time measure the voltage across the resistor V and the current through the resistor I, through the interior of the large scale integrated circuit to complete the voltage divided by the current calculation, and then the results obtained after A/D conversion to digital show resistance, even if the voltage across the resistor V and the current through the resistor I is changed at the same time, the display resistance value is not as common due to high resistance meter that measured voltage or current change of V I change, so, even if the measured voltage, resistance, power supply voltage is measured the changes in the results have little effect, the measurement accuracy is very high ( patent ), theoretically the error can be zero, while the actual error can be done a few thousandths or extremely few.
Typical application
1 measurements of anti-static shoes, conductive shoes resistance value
2, measurement of the antistatic material resistance and resistivity
3, measurement computer room with movable floor system resistance
4, measurement of insulation resistance ( rate)
5, photodiode dark current measurement
6, physics, optics and materials research
Canton company other insulating materials testing instruments:
BDJC-0-100KV dielectric breakdown testing instrument
BDJC series insulating materials at power frequencies of dielectric breakdown test instrument
BDJC series voltage dielectric strength test apparatus
BDJC series voltage breakdown testing instrument
BDJC series insulating paint film breakdown strength tester
BDJC capacitor voltage breakdown testing instrument
EST-121 volume surface resistivity measuring instrument
GDAT-A dielectric loss tester / dielectric constant test
GDAT-C model dielectric constant dielectric loss tester
BDH leakage resistance tester
BDH-B arc resistance tester
China Inspection and certification services tip and intellectual leader, helped many testing quality inspection units and schools and research units to provide comprehensive one-stop quality solutions.
Pay attention to every detail is Canton company for each customer commitment, and North Canton company has been pursuing the aim of. Beijing North Canton precision instrument equipment limited www.beiguangjy.com