NXQ-L25/10-H,NXQ-L1.6/10-H,NXQ-L2.5/10-H液壓囊式蓄能器，蓄能器膠囊，蓄能器皮囊

NXQ-L150/10-H,NXQ-L150/20-H,NXQ-L150/31.5-H液壓囊式蓄能器，蓄能器膠囊，蓄能器皮囊

NXQ-L150/10-H,NXQ-L150/20-H,NXQ-L150/31.5-H液壓囊式蓄能器，蓄能器膠囊，蓄能器皮囊

NXQ-L25/10-H,NXQ-L1.6/10-H,NXQ-L2.5/10-H囊式蓄能器，蓄能器膠囊，蓄能器皮囊

NXQ-L0.25/10-H,NXQ-L0.4/10-H,NXQ-L0.63/10-H
NXQ-L1/10-H,NXQ-L1.25/10-H,NXQ-L4/10-H
NXQ-L6.3/10-H,NXQ-L16/10-H,NXQ-L20/10-H
NXQ-L25/10-H,NXQ-L1.6/10-H,NXQ-L2.5/10-H
NXQ-L10/10-H,NXQ-L40/10-H,NXQ-L63/10-H
NXQ-L80/10-H,NXQ-L100/10-H,NXQ-L125/10-H
NXQ-L150/10-H,NXQ-L150/20-H,NXQ-L150/31.5-H
NXQ-L0.25/20-H,NXQ-L0.4/20-H,NXQ-L0.63/20-H
NXQ-L1/20-H,NXQ-L1.25/20-H,NXQ-L4/20-H
NXQ-L6.3/20-H,NXQ-L16/20-H,NXQ-L20/20-H
NXQ-L25/20-H,NXQ-L1.6/20-H,NXQ-L2.5/20-H
NXQ-L10/20-H,NXQ-L40/20-H,NXQ-L63/20-H
NXQ-L80/20-H,NXQ-L100/20-H,NXQ-L125/20-H
NXQ-L0.25/31.5-H,NXQ-L0.4/31.5-H,NXQ-L0.63/31.5-H
DZ30-1-50B/100XM抗衡閥

A2F160R1P1,A2F160R2P1,A2F160R3P1,A2F160R4P1,A2F160R1P2,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R2P2,A2F160R3P2,A2F160R4P2,A2F160R1P3,A2F160R2P3,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R3P3,A2F160R4P3,A2F160R1P4,A2F160R2P4,A2F160R3P4,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R4P4,A2F160R1P5,A2F160R2P5A2F160R3P5,A2F160R4P5,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R1P6,A2F160R2P6,A2F160R3P6,A2F160R4P6,A2F160R1P7,
A2F160R2P7,A2F160R3P7,A2F160R4P7,A2F160R1Z1,A2F160R2Z1,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R3Z1,A2F160R4Z1,A2F160R1Z2A2F160R2Z2,A2F160R3Z2,柱塞泵,定量柱塞泵，溫納柱塞泵廠家
A2F160R4Z2,A2F160R1Z3,A2F160R2Z3,A2F160R3Z3,A2F160R4Z3,柱塞泵,定量柱塞泵，溫納柱塞泵廠家

A2F160R1Z4,A2F160R2Z4,A2F160R3Z4,A2F160R4Z4,A2F160R1Z5,柱塞泵,定量柱塞泵，溫納柱塞泵廠家

帶定位器使用的調節閥，定位器工作不正常，其氣路節流口堵塞是常見的故障。帶定位器工作時，必須處理好氣源，通常采用的辦法是在定位器前氣源管線上安裝空氣過濾減壓閥。增大節流間隙法：如介質中的固體顆粒或管道中被沖刷掉的焊渣和銹物等因過不了節流口造成堵塞、卡住等故障，可改用節流間隙大的節流件節流面積為開窗、開口類的閥芯、套筒，因其節流面積集中而不是圓周分布的，故障就能很容易地被排除。如果是單、雙座閥就可將柱塞形閥芯改為V形口的閥芯，或改成套筒閥等。