??在平常假如我們常常運用，能夠選
擇干粉顆粒狀聚丙烯酰胺，The classification obtained by the method is different. If the ionic type can be divided into Yin, non, amphoteric and cationic polyacrylamide, if according to the shape, it can be divided into four shapes: colloid, laxity, emulsion and dry powder. Which of these four forms is more suitable for us? The company gives you some suggestions. Next is our experience. I hope you will be interested.
In general, if we often use it, we can choose dry powder granular polyacrylamide. Because of its highest solid content, dry powder polyacrylamide is generally stored in dry and cool places for more than two years, but if mixed with solution, its storage time will be limited. Generally speaking, when the concentration of solution is 0.1%, non-ionic and anionic polyacrylamide will dissolve. The stability of cationic polyacrylamide solution depends on the concentration of the solution. For example, the more concentrated the solution is, the longer the storage time of 3%-5% solution is, but the 3%-5% solution can not be directly used to treat sewage. This solution needs to be diluted before use, and the PH value of cationic polyacrylamide solution is less than 5.5. Stability, if greater than 6.0, will be due to hydrolysis and failure, water medium dispersion polyacrylamide shelf life of six months.說，我們會提到聚丙烯酰胺產品的分子量，但有些客戶會詢問它們的粘度。聚丙烯酰胺的分子量與其粘度有一定的關系。確定聚丙烯酰胺分子量的方法之一是測量其粘度方法。可以看出，聚丙烯酰胺的粘度和分子量之間存在一定的關系！
在正常情況下，聚丙烯酰胺的分子量越高，粘度越大，因為聚丙烯酰胺大分子是細小的長鏈狀體，并且在溶液中的運動阻力很大。粘度的本質是溶液中的摩擦量，也稱為內摩擦系數。各種高分子有機化合物的溶液具有高粘度并隨著分子量的增加而增加。
Therefore, polyacrylamide is still a better choice of solids, can be used with the mix, do not cause waste.
Of course, we must pay attention to the conditions and taboos of preserving polyacrylamide. Polyacrylamide is more sensitive to iron ions, calcium ions and magnesium ions than anionic polymers. In particular, iron ions are catalysts for the chemical degradation of all polyacrylamide. Therefore, in the manufacture, handling and storage of polyacrylamide solutions, we must try to avoid iron ions entering and touching the solution. The equipment should be made of plastics, stainless steel, FRP or carbon steel with surface coating resin.由于它的固含量，一般情況下干粉聚丙烯酰胺在干燥、陰涼的當?shù)厥羌拇娑暌陨系?，但假如配成溶液的話，它的寄存時刻就有限了，一般說，溶液濃度為0.1%的時候，非離子與陰離子聚丙烯酰胺溶液不會超過一周的時刻，陽離子聚丙烯酰胺溶液則不會超過一天，而且溶液的穩定性與溶液的濃度有關，配的濃度越濃，例如3%——5%的溶液寄存時刻越長，但3%——5%的溶液不能直接去處理污水，這種在運用前需要稀釋，陽離子聚丙烯酰胺溶液PH值小于5.5的時后比較穩定，假如大于6.0的話，就會由于水解的原因而失效，水介質渙散型聚丙烯酰胺保質期為六個月。
