Rosemount 2240S-P0840FNA0A2M-Q1

我們的優勢是歐美進口備件配件，所有進口的冷門的停產的或者你們找不到

的產品都可以來找我！

美國西門子ITE全系列、EATON電機 斷路器  接觸器 變壓器 、 GE電氣 斷路

器 接觸器 變壓器 、 Cutler-Hammer（卡特拉-漢莫）、艾默生電機、PQ、

VERSA  這些品牌我們價格都很美好。

歡迎前來詢價！


廈門紀揚科技有限公司是一家以工業自動化為主營，融科、工、貿于一體，

專業從*工業自動化工程項目設計、安裝、調試等服務和*銷售各類進口**

電氣及自動化產品的民營高新技術企業。綜合型的工程技術服務型單位，是

國內專業的電氣產品分銷商及工業自動化系統集成商。

主營：世界知名品牌的PLC 、DCS 系統備件 模塊

①Allen-Bradley(美國AB)系列產品》

②Schneider(施耐德電氣)系列產品》

③General electric(通用電氣)系列產品》

④Westinghouse（美國西屋）系列產品》

⑤SIEMENS(西門子系列產品)》

⑥銷售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots。

⑦estinghouse（西屋）： OVATION系統、WDPF系統、MAX1000系統備件。

⑧Invensys Foxboro（福克斯波羅）：I/A Series系統，FBM（現場輸入/輸出模塊）順序控制、梯形 邏輯控制、事故追憶處理、數模轉換、輸入/輸出信號處理、數據通信及處理等。Invensys Triconex: 冗余容錯控制系統、基于三重模件冗余（TMR）結構的zui現代化的容錯控制器。

⑨Siemens(西門子)：Siemens MOORE， Siemens Simatic C1，Siemens數控系統等。

⑩Bosch Rexroth（博世力士樂）：Indramat，I/O模塊,PLC控制器,驅動模塊等。

◆Motorola（摩托羅拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。

Rosemount   2240S-P0840FNA0A2M-Q1

 
RS-232.
? Usually there are two external serial port jacks on a PC, 
located on the rear panel. Most often, they are either DB-9 or 
DB-25 male (see below).
Note
Model 700 software upgrades can be installed via any available 
communications port. 
Figure 3-19. Serial port jacks
? PC serial ports can be used by other peripheral equipment 
attached to the PC, such as a printer, mouse, or modem, etc. 
To determine which PC serial ports are already being used by 
other equipment and which port can be used for connecting 
to the GC, note existing serial connections, refer to your PC 
user manual, and use diagnostic software (such as Norton 
Utilities).
2. What serial ports are available at the GC? 
The Model 700 without the FID comes equipped with three serial 
ports (standard), unless the customer needs a LOI Interface 
connection, then only two com ports are standard. The 
installation of the optional Com4A board (with or without a LOI) 
brings the total number of available serial ports to six.
System Reference Manual Model 700 Gas Chromatograph
3-9000-521 APRIL 2012
3 - 36
When you select a serial port, consider these points:
? Com1 and Com2 from the WinSystems CPU board (J1) and 
Com4 from the WinSystems CPU board (J6) to Field 
Termination board (J5 and J7) (standard configuration)
? Com3 from WinSystems CPU board (J6) to the multifunction 
board 
? Com4 is reserved for the LOI (Local Operator Interface), if 
installed.
The Model 700 with the FID comes equipped with two serial ports 
(standard). The installation of the optional Com4A board bring 
the total number of available serial ports to six.
When you select a serial port, consider these points:
? Com1 and Com2 from the WinSystems CPU board (J1) to 
Field Termination board (J5 and J7) standard configuration
? Com3 from WinSystems CPU board (J6) to the multifunction 
board (J4)
? Com4 from the WinSystems board (J6) is connected to the 
FID/TCD Preamplifier board (J4)
For additional serial ports, the:
? Optional Com4A board may be installed at the factory. Com5 
through Com8 are fully available to the user and are factoryconfigured to RS-232 protocol. See Appendix A for additional 
options (RS-422/485).
? With the optional Com4A board installed, six Com ports are 
available to the user.
3. Is the connection to be made in a …
? Short distance between the PC and GC?
? With temporary or permanent cable connection?
See Section 3.4.3, FTB connection (RS-232).
4. Is the connection to be made with a …
? Short distance between the PC and GC?
? Permanent cable connection (see Section 3.4.4).
Model 700 Gas Chromatograph System Reference Manual
APRIL 2012 3-9000-521
3 - 37
5. Is the connection to be made with a …
? Long distance between the PC and GC?
? Permanent cable connection (see Section 3.4.5).
3.4.3 FTB connection (RS-232)
The easiest way to connect a PC to the GC is with an off-the-shelf, 
straight-through serial cable connected to the GC serial port DB 9-pin 
connector pre-wired on the FTB.
1. Obtain a straight-through serial cable with these specifications: