- 產品
- 供應
- 公司
- 新聞
|
|
||||||||||||||||||||||||||||
| 是否提供加工定制：否 | 類型：軸流風扇 | 品牌：仁鋼--RG |
| 型號：RG120*120*38MM | 電機功率：15（w） | 電壓：220（V） |
| 電流：0.13（A） | 適用范圍：家用電器，機械設備通用 | 風量：87CFM |
| 轉速：2800RPM |
深圳市仁鋼電子公司專業生產經營全系列交/直流風機，
公司技術力量雄厚、設備齊全、工藝先進，產品遠銷國內外市場。
主要用于投影機，DVD，機箱，電源，功放，移動硬盤，
| 規 格 說 明 書 | ||||||||
| Specifications | ||||||||
| 3、機構 Mechanical | ||||||||
| 3-1、外觀尺寸 External dimension | 120*120*38 MM | |||||||
| 3-2、重量 Weight | 520g(lead wire 80mm& without connector) | |||||||
| 3-3、軸承 Bearing | 滾珠軸承ball bearing | |||||||
| 4、 電氣特性 Electrical characteristics(在通風及額定電壓條件下 in free air at rated voltage) | ||||||||
| 4-1、額定電壓 Rated voltage | 220V | |||||||
| 4-2、額定電流 Rated current | 0.132A | |||||||
| 4-3、額定輸入功率 Rated input power | 16W | |||||||
| 5、 效率 Efficiency | ||||||||
| 5-1、風扇轉數 Rated speed(范圍 range) | 2720RPM | |||||||
| 5-2、最大風量 Maximum air flow | 65CFM | |||||||
| 5-3、最大靜壓 Maximum static air pressure | 0.29Inch-H2O | |||||||
| 6、 特性規格 Characteristics | ||||||||
| 6-1、 操作電壓 Operating voltage range | 175--240V | |||||||
| 6-2、 起動電壓 Staring voltage | 150V(ON/OFF) | |||||||
| 6-3、 鎖定電流 Locked current | 0.165A(Reference) | |||||||
| 6-4、 操作溫度 Operating temperature | -10℃~+70℃ | |||||||
| 6-5、 儲存溫度 Storage temperature | -30℃~+85℃ | |||||||
| 6-6、 環境濕度測試 Environment humidity | 10%(RH)45℃ for 24 hours & 98% (RH) 45℃ for 24 hours | |||||||
| 6-8、 絕緣阻抗強度 Insulation resistance | 在本體與兩條導線間加 500V 直流電壓之絕緣阻抗10MΩ以上 At least 10MΩ at 500 VDC between housing and both lead wires | |||||||
| 6-9、 絕緣耐壓強度 Dielectric strength | 必須能抵抗在本體與兩線間加 1800V 交流電壓1分鐘 1mA Withstand 1800 VAC 1 minute 1mA between housing and both lead wires | |||||||
| 6-10、預期壽命(MTBF)：指在額定電壓及正常溫度，濕度條件下連續運轉。 | ||||||||
| Life ecpectance:continuous operation at rated voltage and normal temperature & humidity | ||||||||
| 6-10-1、含油軸承壽命：20000小時 | ||||||||
| Sleeve bearing life expectance:20000Hours | ||||||||
| 6-10-2、雙滾珠軸承預期壽命：50000小時 | ||||||||
| Two balls bearing life expectance:50000Hours | ||||||||
| 6-11、端子抗拉強度 Tensible strength of connector | 端子以1公斤的拉力拉扯15秒不會脫落 | |||||||
| Connector will not be any broken at 1 Kg for 15 seconds per piece. | ||||||||
| 規 格 說 明 書 | ||||||||
| Specifications | ||||||||
| 11、注意事項(Notes): | ||||||||
| 11-1、使用時請勿超出本規格所規定之極限，否則我們不保證此產品 | ||||||||
| We will not guarantee the products if the application of our products are exceeded the limitation which is specified on this specification. | ||||||||
| 11-2、倘若要變更此份文件的任何規格，請務必事先提出需求 | ||||||||
| In case of changes of the specification specified on this document.A written notice is requested in advance. | ||||||||
| 11-3、請勿觸壓著葉片以及電源線纏繞著風扇或用力拉扯電源線，如此軸心與電源線將會被損毀 | ||||||||
| Please do not touch the impeller with the pressure and never bring the fan with lead wire.The bearing and lead wire may be damaged. | ||||||||
| 11-4、本產品不保證因粉塵、水滴、小蟲進入，而影響壽命與不良品產生 | ||||||||
| No guarantee on the products against the safety problem or failure caused by powder dust, drop of water or insect. | ||||||||
| 11-5、如有任何資料及文件與此份資料不同，將以此份資料為主要參考 | ||||||||
| If there is any data or related documentation different from this data sheet.This data sheet is the principle reference. | ||||||||
| 11-6、請勿在可燃性氣體與任何有害環境中使用 | ||||||||
| Please do not use the fan in the environment of corrosive gas or liquid or any detrimental gas. | ||||||||
| 11-7、當風扇于運轉中，請勿企圖將風扇鎖死特別長的時間，如此，會因連續停止不轉，產生高熱而燒毀風扇 | ||||||||
| While the fan is in operation, please do not lock the fan intentionally for a long periods of time, since the continuous stoppage will result in overheat and thus burnt out the fan | ||||||||
| 11-8、組裝風扇時，請特別注意，因共振或振動產生的噪音 | ||||||||
| During the installation of the fan, please pay substantial attention to possible notice caused by resonance vibration and shock. | ||||||||
| 11-19、當搬運或作業中，風扇如從60cm的高度落下，將會對葉片的平衡產生若干影響，特別是滾珠軸承避免掉落 | ||||||||
| It is very important to notify that avoid to drop from 60cm height when in any movement or operation,it will impact the balance of blade. Especially ball bearing structure is avoided to drop down. | ||||||||
| 11-10、鎖外殼之螺絲扭力不得超 4Kgf | ||||||||
| The torque of the screw which locked the frame should not exceed 4 Kgf |
